Lever ball bearing set for Faema Marte and Mercurio lever groups, only the early curved ones. For the later models Faema Mercurio you need to have a bigger bearing. click there.

This set is suitable for La Pavoni Professional pre millennium.  465225 - Heating element o ring (only for stainless steel heating element) 1x 465204 – boiler knob o ring 1x 362020 – sight glass gasket 2x 465128 – group locking o ring 1x 361005 – piston gasket 2x 465300 – portafilter o ring 1x 362019 - boiler gasket 1x362081 - boiler gasket 1x 361023 -...

Rancilio heating element gasket 59x45x2mm

Faema E61 spout breaker Return to the Faema E61 group parts overview

Vibiemme replica steam pipe left

La Cimbali conical portafilter gasket Internal diameter (mm) 56External diameter (mm) 70Height (mm) 9

On this product page you will find a brass welding cap. These welding caps are soldered to the ends of copper tubes in combination with a welding nut. This round surface seals off when the nut it tightened. The brass material compresses and this seals off the valve. At some point this seal will leak. This is the biggest size of welding fitting you can...

Faema lever group front stop. This stop makes sure that the lever assembly doesn't touch the brewing group when the lever is lowered. Over time the rubber used perishes or get’s damages. You can use this part on the Faema Zodiac lever group, Faema President, Faema Urania, Faema Lambro lever brewing groups. They are also usable for the Faema Marte and...

Faema ring  Return to the Faema Zodiac lever parts overview

La San Marco washer 30X22X1,5mmReturn to the  San Marco group parts overview

The item on this product page is a male 3/8” plug. These plugs have various applications, but mainly as it indicates, closing off something. This male plug is normally used with PTFE tape or with a flat gasket/copper gasket. This male plug has a 3/8” thread, the tread type used is a BSP-G thread. This item has been made in Italy.

E61 group flow restrictor 2mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used at the cam shaft. This spring is compressed in the cam shaft assembly. Due to this compression the cam shaft gaskets will always seal off the shaft. This stainless-steel compression spring has a outer diameter of 15mm. The length of this...

Silicone hose 5x8mm. shore 60

Rancilio water/steam tap

Victoria Arduino supervat portafilter insert screw. This screw will fit a original Victoria Arduino supervat thread. Return to the Victoria Arduino lever parts overview

The heating element on this page is suitable to use on the La San Marco 85 Leva lever espresso machine. The San Marco part reference for this heating element is 108461. This element produces 3000W at 230V. There are in total 4 connecting poles. The immersed length of this element is 375mm. The flange is 82x82mm. This element is mainly for 2 group espresso...

the portafilter gasket on this page is a OEM/Original Bezzera spare part. The Bezzera spare part reference for this item is 7493008. This item is dimension wise and optically the same as the portafilter gasket as in the accessory tab below. But what is the difference. This gasket has a shore number of 90 and the other gasket has a shore number of 75. The...

Connecting wire per 5m brown. made from silicone and fiberglass. copper wire.Section of wire 2,5mm2 (13AWG)

La Pavoni Europiccola and Professional base plate model 1.This model is suitable for the base with the screw hole in the drain pan base

This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...

On this page you will find a brass reduction. This reduction has on one side a female thread and on the other side a male thread. The male thread is a 3/8” BSP-G thread and the female thread is a ½”BSP-G thread. This item has been made from stock brass in Italy. It is possible that you receive the item with a nickel coating.

La San Marco valve body

The rotary vane pump on this page is slightly different then a normal rotary vane pump. This specific model is made by Procon in Ireland. (CO1309BF and 131A060F123B) with a NSF certification The model pump is a clamp on rotary vane pump. The flanges of the pump and motor are pushed against each other and a stainless steel clamp is placed over it and...

A lot of the filterbasket sizes are quite standardized. This IMS filterbasket is good example of this. The basket is made by IMS filtra, but it is a competition basket and not from the standard IMS basket line.  The IMS part number for this double filterbasket is B702TH24.5M. The double filterbasket is made from stainless steel 304, food safe. The outer...

La Cimbali PTFE gasket. the gaskets seals off the closing nut at the top of the brewing group.return to the La Cimbali overview page

Rancilio heating element 2 grp 4300W 230/380V Type flangedwatt 4300volt 230/380vlength (mm) 380

The heating element shown on this page is suitable for various 3 group Faema espresso machine models such as the Faema E61, Faema President and the Faema Urania. This element produces at 220V 3700W. There are 4 connecting poles. The immersed length of the element is 455mm. The flange is a typical Faema style flange of 95x57mm. In the middle of the flange...

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...

On this product page you will find the connection between the lever and the lever group itself. In the top of this casted item you will screw the lever itself.  There are 2 holes. 1 of them has a bushing inside so that there is some axial movement possible. In the fixed hole goes the bearing shaft. In the movable hole goes a pin to make a connection with...

Fitting 3/8" 20mm hex 20

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...

Brass L fitting 1/8" BSP-G MMReturn to the fitting overview

On this page you will find the bottom tube which can be used on various Faema E61 espresso machine models. Note: this item is for the left group when you are standing at the back. The fitting on the boiler side is a female ½”BSP-G thread. On the other side of the tube at the brewing group there is a male fitting which is ½”BSP-G

The item on this page you will find a OEM/Original La Pavoni spare part. This nut can be used on La Pavoni pre-millennium and millennium lever brewing groups. This nut is used as a counter nut for the shaft nut. The La Pavoni part reference for this item is 3135264. This nut has a internal M10 thread. The key size for this nut is 14mm. the height of this...

The brass square pin on this page can be used on the Faema E61 groups and on the Wega E61 style of brewing groups. The Faema part reference for this item is 4161135915 and the Wega part references are W10341 and WY27421013. This square brass pin has a overall length of 11mm. The length and width are 6x6mm. on the inside is a female M3 thread. This square...