Faema E61 brass washer 5.4x3mm is fitted between the gasket valve holder and between the valve guides Return to the Faema E61 group parts overview

The item on this product page is a steam and water valve elastic washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item 01286.0.00.03  These washers are used in a pair in combination with the articulating valve screw, which is used on the steam and water valves. You can use these washers on the Brasilia...

On this product page you will find a brass welding cap. These welding caps are soldered to the ends of copper tubes in combination with a welding nut. This round surface seals off when the nut it tightened. The brass material compresses and this seals off the valve. This size of welding end cap is mainly used for making tubing for pressure switches. So...

This brass filter holder is used on the Faema E61 brewing group. This item has the Faema part reference of 4151135895. This brass filter holder slides over the nozzle in the op of the brewing group. In the widest section is the stainless steel filter placed with a brass ring on top of it. To keep the filter holder in place there is a nozzle spring...

A welding end cap nut is used to put pressure on the welding cap so it seals against the conical surface of it. Once there is not enough pressure from the back from the welding cap nut, the seal won’t work. This type of welding end cap is slightly different then the standard types of caps. To start, this welding end cap is a male thread instead of a...

L fitting 1/4" FF

La San Marco o ring 74.6x5.9mmReturn to the  San Marco group parts overview

Flat copper gasket 19x13.4x1.5mm 1/4"

La San Marco steam/water valve gasket spring

A set of 2 our own custom made laser cut double filter baskets for the arrarex caravelBasket 1: capacity 14 gr Hole dia: 0,25mmBasket 2: capacity 14 gr Hole dia: 0,30 mmWhat is the difference between a laser cut hole diameter of 0,25mm and 0,3 mm?We choose to make two hole diameters, because the flavor of the espresso completely changes. But using the...

Faema Marte/Mercurio lower gasket. this is the gasket which makes the inner sleeve water tight.This sleeve can only be safely removed with a custom made key. you can try it with a punch, this can work. but the chance on damaging the part is also present.Return to the Faema parts overview

The double bipolar switch you see on this page can be used on the La Pavoni Europiccola domestic lever espresso machine. The La Pavoni part reference for this item is 435059. This switch can be used on Pre-millennium as well as millennium models. This double bipolar switch has been rated up to 16A at 250V. On the red switch is 0 an 1 been silk printed. On...

Brass half nut 1/2" BSP-G 6mm Return to our fitting overview

La Pavoni sight glass 106x12mm red line

On this page you will find a OEM/Original shock absorber for the Astoria and Wega lever brewing groups. This absorber is located inside the lever fork. So when the lever is released by accident this rubber shock absorber will absorb some of the force. This absorber is also used when the lever is in rest position This shock absorber can be used on the...

La San Marco washer 30X22X1,5mmReturn to the  San Marco group parts overview

The item on this product page is a brass washer which can be used on various domestic La Pavoni and Gaggia Lever espresso machines. This includes pre-millennium and Millennium brewing group models. This washer is used in the steam valve. This washer spreads the force equally over the shaft gasket. There are 2 washers installed in each valve. The Gaggia...

La Cimbali copper gasket. this part is used to seal off the inspection/cleaning plug on the back side of the M15 brewing group.Rreturn to the La Cimbali Parts overview

Double nipple female 3/8"

On this product page you will find a Stainless steel lever group spring. We had this spring modelled after a original one. The to reach a similar spring rate the coil diameter is slightly different then with a standard steel spring. The spring has a overall length of approximately 168mm and a outer diameter of approximately 46mm. Why approximately? Seen...

Level probe 1/4 125mm

The stainless steel compression spring on this page is used on various Bezzera steam and water valves. The part reference for this Bezzera compression spring is5471504  The compression spring has a outer diameter of 14mm and a height of 10mm. This item can be used on various Bezzera models such as the Bezzera Galatea, Bezzera Ellisse, Bezzera Ebbis,...

The item on this product page is a OEM/Original La Pavoni spare part. This item is a pressure switch manufactured by the Italian company Ma-ter. The La Pavoni part reference for this item is 451308. This pressure switch had been pre-set at 0,8 bar, but the pressure range goes from 0,5 up to 1,2 bar. The fitting used is a male ¼” BSP-G. The microswitch on...

La San Marco lever group left top brewing group screwReturn to the  San Marco group parts overview

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

Valve rod washer 20x6.3x1.5. Suitable for:CodeProducer93.00058 Carimali25012521 Expobar30370100 Expobar4054043423 FaemaL165/9 MarzoccoL165/9B Marzocco00000096 Nuova Simonelli10402040 Sanremo

O ring  5.7x1.9mm nbr

Always wanted to have a new filter basket for your Arrarex Caravel, you can choose now for one type of filter basket.Basket 1: capacity 14 gr Hole dia: 0,25mm  

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This is the spring located in the upper section of the brewing group, in the trumpet/mushroom. This stainless-steel compression spring has a outer diameter of 13mm. The length of this compression spring is 42mm. This spring has been made in Italy. This...

The item on this product page is a group locking gasket for various Aurora Brugnetti brewing groups. As well as the old lever ones as well for the new solenoid valve operated groups. The Brugnetti part reference number for this item is 000460. This gasket is made from a fibre material. The outer diameter is 78mm, the inner diameter is 42mm and thickness...

Victoria Arduino bottomless portafilterReturn to the portafilter overview

This Gicar level regulator is one of the most simple and common level regulators you will find. This model has the current Gicar code of 9.1.40.71G. there are a lot more product codes, you can find those in the extra info tab.This Gicar level regulator has the name NRL30/1E-2C/F and runs on 230Vac.You can find this level regulator on various espresso...

Faema Thermovelox boiler group locking gasket AFM34

On this product page you will find a brass welding cap. These welding caps are soldered to the ends of copper tubes in combination with a welding nut. This round surface seals off when the nut it tightened. This specific welding cap is used with a 8x1mm copper tube. The welding end nut used with this end cap is a 3/8”BSP-G with a internal diameter of...

Dow111 Molykote 6gr

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 58 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are...