Filter by
Categories
Price
€ €
Filter

coffee machine spare parts

Premium Spare Parts for Lever Coffee and Espresso Machines: Enhance Your Brewing Experience

Are you struggling to find high-quality spare parts for your domestic or commercial vintage lever espresso machine or Faema E61 coffee and espresso machines? Look no further! Our store offers a wide selection of premium piston seals, group locking gaskets, fittings, valves, and much more to meet all your brewing needs.

Faema E61 steam/water valve gasket holder

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...
€7.53

Faema E61 heating element 1 group 1500W 230V

The element on this product page is ideal for your antique lever espresso machine, or Faema E61 espresso machine. This heating element has the typical Faema type of brass flange. The element is powered at 230V and supplies 1500W. The immersed length of the element is just 145mm. The heating element gasket used for this element has a outer diameter of 57mm...
€102.48

Gaggia filterbasket 2 coffee 14gr

The filterbasket shown on this product page is a 2 coffee filterbasket suitable solely for a variety of Gaggia espresso machines. Domestic and commercial espresso models. This filter basket has been made by the Italian company IMS Filtri. The part reference for this basket from IMS is GA2T183. Note: this is not a competition basket. This stainless-steel...
€6.19

O ring 6.07x1.78mm Solenoid valve

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...
€0.67

Brass nut 3/8" hole dia 12,5mm h 17mm

The nut on this product page is a weld-end cap nut. This nut is used to install the pipe with the welded end cap on another fitting. This brass nut is used in combination with a welding accessory. The thread inside is a 3/8” BSP-G female thread. The height of the nut is 16mm and the center hole of this nut is 12.5mm. This brass weld nut can be used in...
€4.74

Bezzera boiler gasket 205x150x2mm

The item on this page is a Bezzera boiler gasket.  This gasket is used to seal off the boiler flange and the espresso machine boiler.  The Bezzera part reference numbers for this item are 5492005 and 5492006. This boiler gasket is made from a universal carbo material. The outer diameter is 205mm the inner diameter is 150mm and the thickness is 2mm. There...
€24.96

Welding end cap dia 8 mm nut 1/4"

On this product page you will find a brass welding cap. These welding caps are soldered to the ends of copper tubes in combination with a welding nut. This round surface seals off when the nut it tightened. The brass material compresses and this seals off the valve. At some point this seal will leak. This can be used on various applications in a espresso...
€2.22

Faema E61 engine RPM 300W 230V

The espresso machine motor on this page is made by the Italian electric motor manufacturer RPM. This motor is intended to be used as a exterior motor, so that it isn’t installed inside the machine. The motor is a good motor to use with a vintage espresso machine like the Faema E61. Currently this coffee machine motor can be used on a variety of models...
€225.40

Faema E61 FDA fiber boiler gasket 12 holes 245x205x2mm

On this product page you will find a boiler gasket for some of the Faema E61, Faema President and Faema Lambro espresso machines. This gasket goes in combination with the boilers which have a separate heating element flange and a water level flange or a single boiler with a heating element flange. We have this gasket made from AFM34 in Germany. This...
€33.38

Vibiemme PTFE boiler gasket 165x150x3mm

The gasket shown on this product page can be used on various Vibiemme espresso machine boilers. The Vibiemme part reference for this item is GUARFL205T  This boiler gasket has a outer diameter of 165mm a inner diameter of 150mm and a thickness of 3mm. This gasket has been made from PTFE. Made in Italy. You can use this boiler gasket on the Vibiemme Cubo,...
€24.19

La Pavoni Europiccola heating element 1000+200W 230V

This is the bigger brother of the 1000W 230V heating element, it is the 1200W 230V heating element suitable for the earlier models of La Pavoni Europiccola and La Pavoni Mignon lever espresso machine. This heating element is also a complete stainless steel. The flange is made from a sheet of stainless steel, the outer diameter is 84mm. The coils are made...
€69.02

Safety valve 3/8" 2.0 bar CE PED IV certified

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€11.52

Welding end cap dia 6 mm nut 3/8"

On this product page you will find a brass welding cap. These welding caps are soldered to the ends of copper tubes in combination with a welding nut. This round surface seals off when the nut it tightened. The brass material compresses and this seals off the valve. This size of welding end cap is mainly used for making tubing for pressure switches. So...
€2.97

Faema E61 boiler manometer

This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...
€43.61

Faema E61 pump manometer

On this product page you will find a pump manometer suitable for the vintage Faema E61 but also for the modern Faema E61 Jubilee and the Faema E61 Legend espresso machines. The part reference for the Faema E61 Legend and Jubilee is 3781135801  This pressure gauge has a scale which goes from 0 – 16 bar of pressure. The body has a outer diameter of 52mm and...
€24.38

T fitting 1/2" MMM

On this product page you will find a brass T fitting, which is solely male. This fitting has on each side a male ½”BSP-G thread. This item is made from casted brass and machined afterwards. It is possible that you receive a item which is brass or nickel plated brass.
€13.42

Pressure switch XP110 0.5 - 1.2 Bar 1/4g

On this product page you can find a XP110 pressure switch suitable for the Elektra Microcasa a Leva and the Isomac models Mondiale, Millennium and Tea. The part references for Elektra are01344035. This pressure switch has been manufactured by the company Ma-Ter. The maximum capacity is 15A at 125/250Vac. The maximum working temperature is 125 degree...
€26.00

Faema E61 cup warmer knob

Faema E61 plastic cup warmer knob. This knob is used on 2 locations on the Faema E61. The first location is on the regeneration valve. The second location is on the valve to controle the cup warmer ring. this ring is missing on most machines, but you can't miss the valve on a e61!
€4.78

Plug 3/8" F

The item on this product page is a male 3/8” plug. These plugs have various applications, but mainly as it indicates, closing off something. This male plug is normally used with PTFE tape or with a flat gasket/copper gasket. This male plug has a 3/8” thread, the tread type used is a BSP-G thread. This item has been made in Italy.
€4.03

Why Choose Our Spare Parts?

Our store is dedicated to providing top-notch spare parts designed specifically for lever coffee and espresso machines. Whether you're a home barista or a professional, our premium parts are crafted to ensure optimal performance and longevity for your beloved machine.

Extensive Selection

We understand the importance of having access to a diverse range of spare parts. That's why our inventory includes a variety of piston seals, group locking gaskets, fittings, valves, and more, suitable for both vintage lever espresso machines and Faema E61 models. With our comprehensive selection, you'll be able to find the perfect parts to keep your machine running smoothly.

Custom Solutions

Can't find the exact part you're looking for? Don't worry! Our team is here to help. Simply send us a message with your product inquiries or questions, and we'll be happy to assist you. Additionally, if the part you need is no longer being manufactured, we can explore the possibility of reproducing it to meet your specific requirements.

Conclusion

In conclusion, our store is your ultimate destination for premium spare parts for lever coffee and espresso machines. With our extensive selection, custom solutions, and dedication to customer satisfaction, we're here to ensure that you have everything you need to maintain and enhance your brewing experience. Explore our store today and discover the perfect spare parts for your machine!