Faema E61 spare parts
This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101 This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...
€0.81
Faema e61 rubber foots 25x6mm
It is quite common that the rubber feet of your Faema E61, Faema President, Faema E61 Legend or Faema E61 Jubile will break down. This can be due to age, cracking or just moving around. These rubber feet go in the bottom of the aluminium feet used on all these models, the modern adjustable feet have the part reference of 3515-135 857 and the fixed feet at...
€4.16
Faema E61 steam valve nut gasket 23x18x1mm
Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview
€0.82
Faema E61 square shaft 34mm
On this page you will find a square brass pin. This brass pin is only used in the Faema E61 brewing group. There is no part reference number available for this part used in Faema brewing groups. This brass square shaft has a overall length of 40mm. The square itself is 5x5mm. the thread used is a male M4 thread. This square shaft goes in the bottom...
€3.37
Faema E61 filterbasket single 7gr
Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview
€5.26
Faema E61 PTFE gasket 26x21x2mm
This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...
€1.52
Boiler top fitting 1/2"
If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...
€20.93
Faema E61 Sticker 1 Group
Faema E61 sticker 1 group for the back glass plate of the machine. Return to the Faema E61 body parts overview
€19.22
Faema E61 gasket PTFE 22x16x2mm
The PTFE gasket on this page is used in a variety of E61 Style of brewing groups as well as the Faema E61 brewing group. You can find the gasket with brands such as La Pavoni, Faema, Wega, Grimac, Bezzera, La Scala, Vibiemme and Brasilia. The list of part and model references can be found in the extra info tab. This gasket has been made from PTFE. The...
€1.34
Faema E61 FDA fiber boiler gasket 12 holes 245x205x2mm
On this product page you will find a boiler gasket for some of the Faema E61, Faema President and Faema Lambro espresso machines. This gasket goes in combination with the boilers which have a separate heating element flange and a water level flange or a single boiler with a heating element flange. We have this gasket made from AFM34 in Germany. This...
€33.38
Brewing group gigleur 0.6mm
Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines Return to the Faema E61 group parts overview
€1.74
Faema E61 camme spring 15x25mm
The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used at the cam shaft. This spring is compressed in the cam shaft assembly. Due to this compression the cam shaft gaskets will always seal off the shaft. This stainless-steel compression spring has a outer diameter of 15mm. The length of this...
€1.67
Faema E61 cup warmer knob
Faema E61 plastic cup warmer knob. This knob is used on 2 locations on the Faema E61. The first location is on the regeneration valve. The second location is on the valve to controle the cup warmer ring. this ring is missing on most machines, but you can't miss the valve on a e61!
€4.78
Faema E61 chromed group collector
On this product page you will find a drain sleeve which can be used on the Faema E61 models and on a variety of E61 Style of brewing groups, not all of them will fit. This drain sleeve can be used on the e61 groups of La Scala, Bezzera, Grimac, Faema, Pavoni, Wega and Brasilia. This drain sleeve has been machined from brass and after that it has been...
€72.40
Faema E61 moustache set
On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€31.71
IMS Faema single cup filter basket 7/9 gr
The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. The single filterbasket on this page has the IMS product code B701TH26.5E This single filterbasket can hold ground coffee from 7 grams up to 9grams. The basket...
€25.59
Autofill system lever espresso machine
This autolevel set contains the folowing parts:autofill device 230V; solenoid valve 1/8" 230V; level probe 140 mm; solenoid valve plastic cover; wiring harness; ball valve 1/8"
€120.55
Faema E61 pump manometer
On this product page you will find a pump manometer suitable for the vintage Faema E61 but also for the modern Faema E61 Jubilee and the Faema E61 Legend espresso machines. The part reference for the Faema E61 Legend and Jubilee is 3781135801 This pressure gauge has a scale which goes from 0 – 16 bar of pressure. The body has a outer diameter of 52mm and...
€24.38
Flat copper gasket 23x17x1.5mm
Flat copper gasket 23x17x1.5mm Return to the Faema E61 valve parts overview
€0.96
Sirai pressure switch single phase P203/T01 20A
The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...
€99.17
Faema President and E61 2 group glass
It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...
€303.97
Flex pipe 2000mm 3/8 ff conical base
On this page you will find a stainless steel water hose. This hose can be used to connect the water mains to your espresso machine any other suitable appliance. This stainless steel flex hose has a overall length of 2000mm and on each end a 3/8” BSP-G fitting. This connection is conical so there is no need to a gasket. The maximum fluid temperature which...
€20.35
Stainless steel pressure switch bracket
Pressure switch bracket made out of stainless steel 304. The bracket has a length of 90mm and a width of 18mm. This bracket is intended to fix one side to a boiler stud or inbetween a boiler bolt (up to M10).The other side is suitable to fit a pressure switch with a 1/4" BSP-G connector.
€10.48
Faema E61 plastic top 1 group
On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...
€265.67
Faema E61 plastic top 2 group
On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 2 group are only the measurements of the width and length of the U shape. The length of this plexi is about 455 and the width is 220mm. This plexiglass...
€325.64
Filterholder gasket 72.5x57x8 mm
On this product page you will find a portafilter gasket suitable for a variety of antique Faema espresso machines. As well for the Faema Marte, Faema Mercurio, Faema E61. This portafilter gasket has a outer diameter of 72,5mm a inner diameter of 57mm and a thickness of 8mm. This gasket has been manufactured from NBR. As mentioned before you can use this...
€4.04
E61 brewing group complete rebuild kit
On this product page you will find a rebuild kit for Faema E61 espresso machines. The Faema E61 brewing group is the basis off all the other E61 style of brewing groups made. This does not mean that this kit will fit all those brewing groups. Manufacturers have made over time a lot of changes in the brewing group assemblies, so they are for some...
€93.15
E61 brewing group gasket rebuild kit
E61 brewing group gasket rebuild kit This set is only suitable for the Faema E61 brewing group styles.
€31.68
Faema E61 stickers
On this page you will find the stickers which go on the front panel of the vintage Faema E61 and Faema President lever group. These can get damaged or not present at all. This set contains the Faema water level sticker descriptions, Massimo and Minimo. For the steam valve Vapore, for the water valve Scarico acqua. For the cup warmer valve the Scaldatazze....
€11.07
Faema E61 o ring 18,64x3,53 viton
Faema E61 o ring 18,64x3,53 viton. This o ring seals off the bottom group mushroom. Return to the Faema E61 group parts overview
€1.35
Washer 14x8x1mm brass
On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569 This brass flat washer has a outer diameter of...
€2.09
Safety valve 3/8" 2.0 bar CE PED IV certified
On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€11.52
Faema filterbasket 21gr
The 2 coffee filterbasket on this page can be used a big variety of espresso machine brands. You can use this basket on brands such as Faema, Grimac, Astoria, Wega, Rancilio and Conti. This filterbasket has been made by the Italian company IMS Filtri. The IMS part reference is IMS3T011. Note: this is not a competition filterbasket. This stainless steel...
€6.22
Faema E61 water level spring
The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...
€3.82
Faema E61 flange level side
Faema E61 flange sight glass side. Do you have a small leak in one of your boiler flanges. this can be fixed easily by replacing the flange which is leaking. Next to the level side flange we also offer the heating element side flange. Return to the Faema E61 boiler parts overview
€403.94
