Faema E61 spare parts
This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.24
Faema E61 FDA fiber boiler gasket 12 holes 245x205x2mm
On this product page you will find a boiler gasket for some of the Faema E61, Faema President and Faema Lambro espresso machines. This gasket goes in combination with the boilers which have a separate heating element flange and a water level flange or a single boiler with a heating element flange. We have this gasket made from AFM34 in Germany. This...
€33.38
IMS Faema double cup filterbasket 12/18gr
A lot of the filterbasket sizes are quite standardized. This IMS filterbasket is good example of this. The basket is made by IMS filtra, but it is a competition basket and not from the standard IMS basket line. The IMS part number for this double filterbasket is B702TH24.5M. The double filterbasket is made from stainless steel 304, food safe. The outer...
€28.03
E61 group allen key copper washer 10x6,2x1mm
Almost every Faema e61 brewing group made has a Allen bolt on the front of the brewing group, yes there are models which don’t have this hole. This hole also needs to be sealed off. This can be done with PTFE tape. But you can also use a copper gasket for that. The Faema part reference for this item is 4054043102 This flat copper washer has a outer...
€0.60
Faema E61 inox filter 10.5x0.3mm
On this page you will find a small stainless steel water filter. This filter mesh goes into the top of the Faema E61 brewing groups. This filter membrane prevents clogging up of the nozzle in the group. The Faema part reference for this item is 4771135894. This wire mesh membrane is made from stainless steel and has a outer diameter of 10,mm and a...
€1.82
Autofill system lever espresso machine
This autolevel set contains the folowing parts:autofill device 230V; solenoid valve 1/8" 230V; level probe 140 mm; solenoid valve plastic cover; wiring harness; ball valve 1/8"
€120.55
E61 brewing group gasket rebuild kit
E61 brewing group gasket rebuild kit This set is only suitable for the Faema E61 brewing group styles.
€31.68
Portafilter gasket 73x57x9mm
Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.59
Faema E61 non return valve body
Faema E61 brass non return valve body. The side flange is screwed into the main body.If you want to complete the assembly add the following parts to the part:Faema E61 Spring Non Return Valve; O Ring EPDM 8,9x1,9mm; Faema E61 Small Non Return ValveReturn to the Faema E61 valve parts overview
€33.38
Faema E61 chromed group collector
On this product page you will find a drain sleeve which can be used on the Faema E61 models and on a variety of E61 Style of brewing groups, not all of them will fit. This drain sleeve can be used on the e61 groups of La Scala, Bezzera, Grimac, Faema, Pavoni, Wega and Brasilia. This drain sleeve has been machined from brass and after that it has been...
€72.40
Asco pressure switch P302/6
The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...
€81.48
IMS E61 style shower screen
This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....
€25.03
Faema E61 filterbasket single 7gr
Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview
€5.26
Safety valve 3/8'' 1,8 bar
On this page you will find a safety valve which has a male 3/8”BSP-G thread. The pre-set pressure of this valve is 1,8bar. You can adjust it yourself but not recommended. The spring inside the safety valve is made from stainless steel and the sealing material is FKM. The valve has been made in Italy. We do strongly advise to replace the safety valve every...
€16.80
Faema E61 heating element 1 group 1500W 230V
The element on this product page is ideal for your antique lever espresso machine, or Faema E61 espresso machine. This heating element has the typical Faema type of brass flange. The element is powered at 230V and supplies 1500W. The immersed length of the element is just 145mm. The heating element gasket used for this element has a outer diameter of 57mm...
€102.48
Crushable copper washer 23x17x3mm
The crushable copper gasket on this page can be used with various applications on Brasilia espresso machines. For instance, on sealing off steam and water tubes and as a gasket on various boiler fitting applications. The Brasilia part reference for this item is 01386.0.00.02 This copper gasket has a outer diameter of 23mm a inner diameter of 17mm and a...
€1.72
Faema E61 glass plate srew set
Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€54.91
Faema E61 moustache set
On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€31.71
Faema E61 sight glass 12x175mm
The sight glass on this page is used on a variety of Lever espresso machines by the brand Faema. This sight glass can be used on models such as the Faema E61, Faema President and the Faema Lambro espresso machine. The sight glass has a outer diameter of 12mm and a overall length of 175mm. This sight glass has been made in Italy. The gasket you need for...
€5.74
Boiler top fitting 1/2"
If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...
€20.93
Faema E61 sticker 2 group
Faema E61 sticker 2 group for the glass plate on the back of the machine. Is your glass plate broken, we do also offer a new glass plate for this sticker. And to finish it off a new set of glass plate nuts Return to the Faema E61 body parts overview
€26.65
Brewing group gigleur 0.6mm
Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines Return to the Faema E61 group parts overview
€1.74
IMS faema double cup filterbasket 18/22gr
The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. This double filterbasket on this page has the IMS product code B702TCH28.5E or B702TH28.5E This single filterbasket can hold ground coffee from 18 grams up to...
€25.03
Faema E61 valve gasket 15,5x7,5x4mm
This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...
€0.81
Faema E61 stainless steel valve rod
On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...
€14.47
E61 valve guide 12mm
In the Faema E61 and E61 style brewing groups you can find a variety of square valve pins, in different shapes and heights. This square pin screws into the M3 thread situation on the valve gasket holder. This model is one of the more common model which is used with brands such as Wega, Faema and La Pavoni. The part references are for Wega WY27421012,...
€1.74
Faema E61 group collector rod gasket holder
The item on this page is a gasket holder which is used in a variety of E61 brewing groups. You can find this item in some valve assemblies used on Faema, Pavoni and Wega espresso machines. For some brands this item is also used in the steam/water and water inlet valves. This brass gasket holder has 2 threads. 1 female and one male. The female thread is a...
€4.84
O ring nbr 8,9x1,9mm
This O ring in nbr with the specifications 8,9x1,9mm. Makes sure that the brass non return valve seals against the body of the non return valve. Return to the Faema E61 valve parts overview
€0.65
Faema E61 upper round rod
Faema E61 brass upper round rod 40x4mm. screws in the valve gasket holder Return to the Faema E61 group parts overview
€3.50
Faema glass support set
It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...
€49.83
Faema E61 heating element 3 group 3700W 230V
The heating element shown on this page is suitable for various 3 group Faema espresso machine models such as the Faema E61, Faema President and the Faema Urania. This element produces at 220V 3700W. There are 4 connecting poles. The immersed length of the element is 455mm. The flange is a typical Faema style flange of 95x57mm. In the middle of the flange...
€94.05
Faema E61 water level spring
The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...
€3.82
Faema E61 expansion valve guide
Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview
€5.11
IMS Faema single cup filter basket 7/9 gr
The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. The single filterbasket on this page has the IMS product code B701TH26.5E This single filterbasket can hold ground coffee from 7 grams up to 9grams. The basket...
€25.59
Faema E61 o ring 18,64x3,53 viton
Faema E61 o ring 18,64x3,53 viton. This o ring seals off the bottom group mushroom. Return to the Faema E61 group parts overview
€1.35
Faema E61 expansion valve spring
Faema E61 stainless steel expansion valve spring. This spring has a total length of 32.5mm and a external diameter of 15mm.This spring makes sure that the valve opens at the right over pressure. Return to the Faema E61 valve parts overview
€2.42
