Faema E61 spare parts

The Faema E61: A Revolutionary Espresso Machine

The Faema E61 espresso machine is an iconic espresso machine with a timeless design that has revolutionized the espresso machine market. Introduced in the 1961, the Faema E61 marked a significant shift in the way espresso was made, setting new standards for quality and consistency in espresso extraction.

Faema Spare Parts - E61

Faema E61 group valve guide 11mm

The brass square pin on this page can be used on the Faema E61 groups and on the Wega E61 style of brewing groups. The Faema part reference for this item is 4161135915 and the Wega part references are W10341 and WY27421013. This square brass pin has a overall length of 11mm. The length and width are 6x6mm. on the inside is a female M3 thread. This square...
€1.83

Faema E61 steam/water valve gasket holder

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...
€6.84

Faema E61 group spring 14x33mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the bottom exhaust valve. When the lever is in the lowest position the valve assembly will push this spring inward and the exhaust valve will open completely. This will make sure that all the exhaust water goes out...
€2.17

Faema front bakelite knob set

It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...
€36.70

Faema E61 brass camme lever rod

The item shown on this page is a cam shaft which is used on the Faema E61 and various other E61 style of brewing groups.  Such as Bezzera and La Pavoni e61 style groups. The Faema part reference for this item 3161136650, the Bezzera part reference is 7479950 and for La Pavoni the reference is 314077. This brass cam shaft has a overall length of 82mm. The...
€18.27

Asco/Sirai pressure switch P303/T01 3 phase 20A

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€88.64

Flex pipe 1500mm 3/8 FF conical base

The flexible tube on this page has a overall length of 1500mm. This includes the fittings. The fittings on this pipe are female 3/8” BSP-G and both have a conical base, so there is no gasket needed. The tubes are rated up to 10 bar and with a maximum working temperature of 90 degree Celsius.
€17.11

Faema E61 left lower group tube

On this page you will find the bottom tube which can be used on various Faema E61 espresso machine models. Note: this item is for the left group when you are standing at the back. The fitting on the boiler side is a female ½”BSP-G thread. On the other side of the tube at the brewing group there is a male fitting which is ½”BSP-G
€59.72

Faema E61 camme spring 15x25mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used at the cam shaft. This spring is compressed in the cam shaft assembly. Due to this compression the cam shaft gaskets will always seal off the shaft. This stainless-steel compression spring has a outer diameter of 15mm. The length of this...
€1.52

Faema E61 square shaft 34mm

On this page you will find a square brass pin. This brass pin is only used in the Faema E61 brewing group. There is no part reference number available for this part used in Faema brewing groups. This brass square shaft has a overall length of 40mm. The square itself is 5x5mm. the thread used is a male M4 thread. This square shaft goes in the bottom...
€3.06

E61 style groups shower without welding 60mm

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...
€3.02

Faema E61 water level gasket 21x11.4x5mm

The sight glass gasket on this page is used in a variety of older Faema espresso machines such as the Faema E61, Faema President and Faema Lambro. This gasket has been made from EPDM. The outer diameter of this gasket is 21mm the inner diameter is 11,5mm and the thickness is 5mm. This gasket has been made in Germany.
€1.38

Flex pipe 2000mm 3/8 ff conical base

On this page you will find a stainless steel water hose. This hose can be used to connect the water mains to your espresso machine any other suitable appliance. This stainless steel flex hose has a overall length of 2000mm and on each end a 3/8” BSP-G fitting. This connection is conical so there is no need to a gasket. The maximum fluid temperature which...
€18.50

Faema E61 sleeve

The brass cam guide bushing shown on this page is used on the Faema E61 and E61 style brewing groups.  You can use this guide bushing on Faema, Grimac, Vibiemme, La Scala, Bezzera, Wega, Pavoni espresso machines. This brass bushing has a overall length of 28mm. The outer diameters are 10 and 15mm. The inner diameter is 8mm and the head thickness is 5mm....
€3.16

Faema E61 complete upper pipe

On this product page you will find the complete upper pipe for various E61 style and Faema E61 brewing groups. This item can be used in various E61 style brewing groups such as the ones used on the La Pavoni, Isomac and EC Heidelberg. But also on the Faema E61, Faema E61 Legend and the Faema E61 Jubilee espresso machines. The Faema part reference is...
€30.34

Compression spring 13x42mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This is the spring located in the upper section of the brewing group, in the trumpet/mushroom. This stainless-steel compression spring has a outer diameter of 13mm. The length of this compression spring is 42mm. This spring has been made in Italy. This...
€2.02

Faema E61 microswitch 16A 250V

On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...
€41.19

Faema President and E61 2 group glass

It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...
€276.34

Safety valve 3/8'' 1,8 bar

On this page you will find a safety valve which has a male 3/8”BSP-G thread. The pre-set pressure of this valve is 1,8bar. You can adjust it yourself but not recommended. The spring inside the safety valve is made from stainless steel and the sealing material is FKM. The valve has been made in Italy. We do strongly advise to replace the safety valve every...
€15.27

Faema E61 glass plate srew set

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€49.92

Faema E61 filterbasket single 7gr

Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview
€5.26

Faema E61 gasket PTFE 22x16x2mm

The PTFE gasket on this page is used in a variety of E61 Style of brewing groups as well as the Faema E61 brewing group. You can find the gasket with brands such as La Pavoni, Faema, Wega, Grimac, Bezzera, La Scala, Vibiemme and Brasilia. The list of part and model references can be found in the extra info tab. This gasket has been made from PTFE. The...
€1.34

Faema E61 single portafilter

The portafilter on this page looks like a classical Faema E61 portafilter. And that is indeed correct, the style looks quite similar to the antique portafilters used in the Faema Lever brewing groups and Faema E61. But there are some slight differences, the shape is slightly different and the end plug in the portafilter handle is not identical to the...
€100.04

Faema E61 plastic top 2 group

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 2 group are only the measurements of the width and length of the U shape. The length of this plexi is about 455 and the width is 220mm. This plexiglass...
€296.04

E61 style lever brewing group

On this product page you will find a complete E61 style brewing group. There are a variety of E61 style brewing groups. Examples of this are the Solenoid valve groups, with the solenoid valve at the bottom, or on the sides. This E61 style brewing group can be used on Fiorenzato, Grimac and La Scala espresso machines. The Fiorenzato part reference fort his...
€365.68

Stainless steel clamp for motor/pump

With this motor clamp ring you are able to clamp a flange pump with a motor with a flange motor. The clamp has been made from stainless steel as well for the clamping screw which comes with it. The items have been made in Italy This item is not suitable in combination with pumps used for instance used on the Faema E61 Legend and the Faema E61 Jubile...
€5.14

Faema E61 steam/water group expanding spring

The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...
€2.25

Faema E61 non return valve body

Faema E61 brass non return valve body. The side flange is screwed into the main body.If you want to complete the assembly add the following parts to the part:Faema E61 Spring Non Return Valve; O Ring EPDM 8,9x1,9mm; Faema E61 Small Non Return ValveReturn to the Faema E61 valve parts overview
€30.34

Faema E61 group net holder

This brass filter holder is used on the Faema E61 brewing group. This item has the Faema part reference of 4151135895. This brass filter holder slides over the nozzle in the op of the brewing group. In the widest section is the stainless steel filter placed with a brass ring on top of it. To keep the filter holder in place there is a nozzle spring...
€2.43

History of the Faema E61

The Faema E61 was introduced in 1961 by the Italian espresso machine manufacturer Faema. It was designed by renowned engineer Ernesto Valente and quickly gained popularity for its innovative features and exceptional performance. One of the key innovations of the Faema E61 was its E61 brewing group, which replaced the traditional lever-operated espresso machines with a more efficient and consistent pump-operated system.

Technical Advancements

The Faema E61 brewing group introduced a number of technical advancements that set it apart from traditional espresso machines. One of the most notable features of the E61 group was its constant pump pressure of 9 bar, which ensured optimal extraction and consistency in every shot of espresso. This revolutionary design paved the way for a new generation of espresso machines and became the basis for many espresso machine manufacturers.

Our Selection of Faema E61 Spare Parts

At our store, we offer a wide selection of spare parts for the Faema E61 espresso machine. Whether you need boiler parts, steam/water valves, body parts, valve parts, brewing group parts, water level parts, pump parts, or water inlet parts, we have you covered. We stock a variety of genuine Faema E61 parts, ensuring that you can find exactly what you need to keep your espresso machine running smoothly.

Faema E61 Models

The Faema E61 espresso machine was produced in various configurations, ranging from 1-group to 6-group models. While the most common models are the 1-group, 2-group, and 3-group versions, there are also larger models available for high-volume commercial settings. Each model features the same innovative E61 brewing group, ensuring consistent performance and quality across the board.

Conclusion

The Faema E61 espresso machine is a true icon of the espresso world, known for its exceptional quality, timeless design, and groundbreaking innovation. With our selection of spare parts, you can keep your Faema E61 running smoothly for years to come, ensuring that you continue to enjoy delicious espresso beverages with every shot. If you have any questions or need assistance finding the right parts for your machine, don't hesitate to reach out to us. We're here to help you keep your Faema E61 in top condition.