Faema E61 Legend

Faema E61 Legend parts

This page is dedicated to parts for the Faema E61 Legend. This machine was re-introduced around the turn of the century. The faema Legend was made 3 configurations:

·          Faema E61 Legend S1;

·          Faema E61 Legend S2;

·          Faema E61 Legend S3

Esthetically the Faema E61 looks quite a lot like the Faema E61 Legend espresso machine. But technically there are quite a lot off differences.

Water level, the water level used in the Faema E61 legend is one with a casted housing with a sight glass in front. This model is also used on a variety of Faema models like: Faema E92, Faema E97, Faema due and so on   And a variety of La Cimbali models like the La Cimbali M39 and the La Cimbali M39 GT

The pump and motor are nowadays installed inside the machine, traditionally the pump and motor on the Faema e61 could be found outside the machine.

On the Faema E61 legend you can now also find standard a autofill system. So the chance that your heating element will dry boil, because of the lack off water, also reduced a lot. The installation of a safety thermostat inside the element also reduced this a lot.

A other item which has been changed over the time. Is that the traditional mercury pressure switch has been replaced by a new model from Asco (this used to be Sirai)

If you have any questions about your Faema E61 legend espresso machine, don’t hesitate to contact us.

Faema E61 legend

Faema E61 glass plate srew set

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€39.80

Portafilter gasket 73x57x9mm

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€3.33

Faema E61 steam tap gasket press

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...
€1.85

Faema E61 Legend and Jubilee front lower feet

These machine feet are used on the Faema E61 Legend and the Faema E61 Jubilee. They can be used on the front left as the front right feet, which have both the part number 3515-135 856. These feet do come with the rubber insert 4991-136 040 These feet are made from polished aluminium. The top section has a diameter of 35mm and the bottom section has a...
€48.15

Portafilter gasket 73x57x9mm red silicone

On this product page you will find a portafilter gasket, but not a standard one. This portafilter gasket has been made from food grade silicone, in the colour red.  This product has been made in Italy. The gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 9mm. You can use this on a variety of brands such as the Vibiemme...
€3.60

Brewing group gigleur 0.6mm

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview
€1.26

Faema E61 legend pump motor

Where the classic Faema E61 espresso machine had a external motor. The Faema E61 Legend and Faema E61 jubilé has a internal espresso machine motor. The motor used in a Faema E61 legend and Jubile is made by Elettromeccanica Ing F. Arduini and has 150W with 230V 50-60Hz. To start the motor there is a condenser installed of 10 µf. The coffee machine motor...
€208.00

Faema E61 small square rod 6mm

On this product page you will find a key component for a Faema E61 and Wega E61 style brewing group. this square brass valve pin has the Faema part reference of 4161135916 and the Wega part reference of W10349. This small brass valve pin screws on top of a gasket holder. The square is 6x6mm. In the middle is a female M3 thread. This item has been made in...
€1.15

Faema E61 Net holder washer 9.8x6.3x1mm

On this page you will find a brass washer which is used in the E61 brewing groups made by Faema. The part references for this item can be found back in the extra info tab. The gasket is used on top of the stainless-steel nozzle filter. The nozzle spring is pushing against this washer to get a equal amount of pressure against the filter This brass washer...
€0.96

Faema E61 group infusion spring 14x45mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the top exhaust valve. When the lever is in the raised position this spring will keep the drain valve in the closed position. This stainless-steel compression spring has an outer diameter of 14mm. The length of...
€1.29

Portafilter gasket suplement 72x58x0.8mm

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...
€0.61

Faema E61 filterbasket double 12gr

Stainless steel double filterbasket for a Faema E61 brewing group. This basket can contain 12grams of coffee. The width of the basket is 70mm and the height of the basket is 22mm.if you are looking for a single filterbasket click there. Return to the Faema E61 group parts overview
€5.15

Faema E61 group valve guide 11mm

The brass square pin on this page can be used on the Faema E61 groups and on the Wega E61 style of brewing groups. The Faema part reference for this item is 4161135915 and the Wega part references are W10341 and WY27421013. This square brass pin has a overall length of 11mm. The length and width are 6x6mm. on the inside is a female M3 thread. This square...
€1.46

Stainless ball 8mm

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...
€1.89

Faema E61 PTFE gasket 26x21x2mm

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...
€1.10

Level indicator red ball

This red ball is a level indicator ball. This ball floats inside the water level tube. Seen it’s not always easy to see the water level makes a floating red ball it a lot easier. There are more colours available with different diameter of balls. This red ball has a diameter of 5,8mm and is made in Italy. This type of level indicator can be found in a...
€1.74

Asco pressure switch P302/6

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...
€83.48

IMS E61 style shower screen

This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....
€21.18

Filterholder gasket 72.5x57x8 mm

On this product page you will find a portafilter gasket suitable for a variety of antique Faema espresso machines. As well for the Faema Marte, Faema Mercurio, Faema E61. This portafilter gasket has a outer diameter of 72,5mm a inner diameter of 57mm and a thickness of 8mm. This gasket has been manufactured from NBR. As mentioned before you can use this...
€2.92

E61 valve guide 12mm

In the Faema E61 and E61 style brewing groups you can find a variety of square valve pins, in different shapes and heights. This square pin screws into the M3 thread situation on the valve gasket holder. This model is one of the more common model which is used with brands such as Wega, Faema and La Pavoni. The part references are for Wega WY27421012,...
€1.26