Filter by
Price
€ €
Filter

Faema E61 Jubilé

Faema E61 Jubilee spare parts

The Faema E61 legend and the Faema E61 jubilee are re-introduced around the turn of the century. The design was kept the same, but technically the machine was updated to with modern features. Like replacing the mercury switch with a modern Sirai pressure switch, temperature probe and with the newer machines a internal pump.

With the introduction of the Faema E61 jubilee lifted the traditional machine to a new level. This model is solenoid operated instead of with the manual valves like with the original Faema E61. Which is standard for a modern espresso machine.

In this overview you can find most parts for the Faema E61 legend and Faema E61 jubilee espresso machine. If you can't find the parts your looking for just send a email.

Faema E61 Jubilé spare parts
Faema E61 plastic top 1 group Faema E61 plastic top 1 group

    Faema E61 plastic top 1 group

    On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...
    €265.67
    compare
    Quick-view
    Stainless steel flex pipe 1500mm 3/8 FF conical base Stainless steel flex pipe 1500mm 3/8 FF conical base

      Flex pipe 1500mm 3/8 FF conical base

      The flexible tube on this page has a overall length of 1500mm. This includes the fittings. The fittings on this pipe are female 3/8” BSP-G and both have a conical base, so there is no gasket needed. The tubes are rated up to 10 bar and with a maximum working temperature of 90 degree Celsius.
      €18.82
      compare
      Quick-view
      Faema e61 rubber foots 25x6mm Faema e61 rubber foots 25x6mm

        Faema e61 rubber foots 25x6mm

        It is quite common that the rubber feet of your Faema E61, Faema President, Faema E61 Legend or Faema E61 Jubile will break down. This can be due to age, cracking or just moving around. These rubber feet go in the bottom of the aluminium feet used on all these models, the modern adjustable feet have the part reference of 3515-135 857 and the fixed feet at...
        €4.16
        compare
        Quick-view
        Faema E61 filterbasket single 7gr Faema E61 filterbasket single 7gr

          Faema E61 filterbasket single 7gr

          Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview
          €5.26
          compare
          Quick-view
          Faema E61 Net holder washer 9.8x6.3x1mm Faema E61 Net holder washer 9.8x6.3x1mm

            Faema E61 Net holder washer 9.8x6.3x1mm

            On this page you will find a brass washer which is used in the E61 brewing groups made by Faema. The part references for this item can be found back in the extra info tab. The gasket is used on top of the stainless-steel nozzle filter. The nozzle spring is pushing against this washer to get a equal amount of pressure against the filter This brass washer...
            €1.32
            compare
            Quick-view
            Washer 14x8x1mm brass Washer 14x8x1mm brass

              Washer 14x8x1mm brass

              On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569  This brass flat washer has a outer diameter of...
              €2.09
              compare
              Quick-view
              Level indicator red ball Level indicator red ball

                Level indicator red ball

                This red ball is a level indicator ball. This ball floats inside the water level tube. Seen it’s not always easy to see the water level makes a floating red ball it a lot easier. There are more colours available with different diameter of balls. This red ball has a diameter of 5,8mm and is made in Italy. This type of level indicator can be found in a...
                €2.40
                compare
                Quick-view
                Faema E61 boiler manometer Faema E61 boiler manometer

                  Faema E61 boiler manometer

                  This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...
                  €43.61
                  compare
                  Quick-view
                  Faema E61 filterbasket double 12gr Filterbasket double 14gr 70x22mm

                    Faema E61 filterbasket double 12gr

                    Stainless steel double filterbasket for a Faema E61 brewing group. This basket can contain 12grams of coffee. The width of the basket is 70mm and the height of the basket is 22mm.if you are looking for a single filterbasket click there. Return to the Faema E61 group parts overview
                    €7.10
                    compare
                    Quick-view
                    Faema E61 valve gasket 15,5x7,5x4mm Faema E61 valve gasket 15,5x7,5x4mm

                      Faema E61 valve gasket 15,5x7,5x4mm

                      This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...
                      €0.81
                      compare
                      Quick-view
                      Faema E61 glass plate srew set Faema E61 glass plate srew set

                        Faema E61 glass plate srew set

                        Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
                        €54.91
                        compare
                        Quick-view
                        Faema E61 Legend and Jubilee front lower feet Faema E61 Legend and Jubilee front lower feet

                          Faema E61 Legend and Jubilee front lower feet

                          These machine feet are used on the Faema E61 Legend and the Faema E61 Jubilee. They can be used on the front left as the front right feet, which have both the part number 3515-135 856. These feet do come with the rubber insert 4991-136 040 These feet are made from polished aluminium. The top section has a diameter of 35mm and the bottom section has a...
                          €55.37
                          compare
                          Quick-view
                          Faema E61 complete steam valve Faema E61 complete steam valve

                            Faema E61 complete steam valve

                            The steam and water valve on this page can be found on various old and new Faema models. The Faema part reference for this item is 903743000  This valve has on the steam/water tube side a female thread of 3/8” BSP-G. On the inlet side the thread is a male 3/8” BSP-G. This steam/water valve does not come with a knob. You can also use the original Bakelite...
                            €77.47
                            compare
                            Quick-view
                            Safety valve 3/8" 2.0 bar CE PED IV certified Safety valve 3/8" 2.0 bar CE PED IV certified

                              Safety valve 3/8" 2.0 bar CE PED IV certified

                              On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
                              €11.52
                              compare
                              Quick-view
                              Faema E61 stainless steel valve rod Faema E61 stainless steel valve rod

                                Faema E61 stainless steel valve rod

                                On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...
                                €14.47
                                compare
                                Quick-view
                                Asco (Sirai) pressure switch P302/6 Asco (Sirai) pressure switch P302/6

                                  Asco pressure switch P302/6

                                  The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...
                                  €81.48
                                  compare
                                  Quick-view
                                  Faema front bakelite knob set Faema front bakelite knob set

                                    Faema front bakelite knob set

                                    It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...
                                    €40.37
                                    compare
                                    Quick-view
                                    Anti vacuum valve TV 1/4" Anti vacuum valve TV 1/4"

                                      Anti vacuum valve TV 1/4"

                                      Anti vacuum valve TV 1/4". Suitable for:CodeProducerA10220 Astra000634 Aurora-brugnetti7452502 Bezzera05062.4.00.09 Brasilia01.00504 Carimali418-911-002 Cimbali418-911-010 Cimbali418911010 Cimbali408898 ContiC219900560 Ecm00200034 Elektra65000205 Expobar2161-118968 Faema2161118968 Faema418911002 Faema...
                                      €10.56
                                      compare
                                      Quick-view
                                      Faema E61 legend jubilee portafilter double Faema E61 legend jubilee portafilter double

                                        Faema E61 legend jubilee portafilter double

                                        On this product page you will find a double portafilter which is suitable for the Faema E61 Legend and the Faema E61 Jubilé espresso machines. The part reference number for this item is 2771-135 803.The portafilter has 2 ears oriented at 90 degree. The ears have a thickness of 6,3mm. The spout connection on this portafilter is a 3/8” BSP-G thread. This...
                                        €100.01
                                        compare
                                        Quick-view
                                        Faema E61 steam tap gasket press Faema E61 steam tap gasket press

                                          Faema E61 steam tap gasket press

                                          This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...
                                          €2.32
                                          compare
                                          Quick-view
                                          Anti vacuum valve V.A.R. 1/4" Anti vacuum valve V.A.R. 1/4"

                                            Anti vacuum valve V.A.R. 1/4"

                                            On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
                                            €12.00
                                            compare
                                            Quick-view
                                            Faema E61 steam/water valve gasket holder Faema E61 steam/water valve gasket holder

                                              Faema E61 steam/water valve gasket holder

                                              On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...
                                              €7.53
                                              compare
                                              Quick-view
                                              Rubber pump motor connector 35mm Rubber pump motor connector 35mm

                                                Rubber pump motor connector 35mm

                                                The item on this page is a rubber motor coupling. This coupling can be used on various Faema and Cimbali espresso machines. There are 2 types of couplings the 35mm and the 40mm coupling. This is the 35mm This coupling is used on the Faema E61 legend and Faema E61 Jubilee espresso machines, the 40mm coupling won’t fit this application. The Faema part...
                                                €12.67
                                                compare
                                                Quick-view
                                                Faema E61 heating element gasket 57x43x3mm Faema E61 heating element gasket 57x43x3mm

                                                  Faema E61 heating element gasket 57x43x3mm

                                                  On this page you will find a heating element gasket we had made out of AFM34 a food safe fibre material, made in Germany. This heating element gasket has a outer diameter of 57mm a inner diameter of 43mm and a thickness of 3mm. This heating element gasket can be used on a variety of heating elements such as the Faema E61, Faema E61 Legend, Faema E61...
                                                  €4.89
                                                  compare
                                                  Quick-view
                                                  Faema E61 gasket PTFE 36.5x30x2mm Faema E61 gasket PTFE 36.5x30x2mm

                                                    Faema E61 gasket PTFE 36x30x2mm

                                                    The PTFE gasket on this page can be used on various E61 style and Faema E61 brewing groups. You can use this gasket on the E61 style brewing groups of the brands like La Scala, Grimac, Wega and La Pavoni.  The part and model references can be found in the extra info tab. This PTFE gasket has a outer diameter of 36mm a inner diameter of 30mm and a...
                                                    €1.04
                                                    compare
                                                    Quick-view