0
My cart
Faema E61 Jubilé
Safety valve 3/8" 2.0 bar CE PED IV certified
On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€10.47
Faema E61 Net holder washer 9.8x6.3x1mm
On this page you will find a brass washer which is used in the E61 brewing groups made by Faema. The part references for this item can be found back in the extra info tab. The gasket is used on top of the stainless-steel nozzle filter. The nozzle spring is pushing against this washer to get a equal amount of pressure against the filter This brass washer...
€1.20
Faema E61 legend pump motor
Where the classic Faema E61 espresso machine had a external motor. The Faema E61 Legend and Faema E61 jubilé has a internal espresso machine motor. The motor used in a Faema E61 legend and Jubile is made by Elettromeccanica Ing F. Arduini and has 150W with 230V 50-60Hz. To start the motor there is a condenser installed of 10 µf. The coffee machine motor...
€260.91
Anti vacuum valve V.A.R. 1/4"
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€10.91
Faema charging valve o ring 4.2x1.9mm
Faema charging valve o ring 4.2x1.9mmReturn to the Faema E61 Legend water inlet parts overview
€0.89
Faema E61 moustache set
On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€28.82
Faema E61 steam/water valve gasket holder
On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...
€6.84
Faema E61 steam/water group expanding spring
The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...
€2.25
O-ring 17,17X1,78mm EPDM
O-ring 17,17X1,78mm EPDMReturn to the Faema E61 Legend water inlet parts overview
€2.26
Stainless ball 8mm
The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...
€2.37
Faema E61 legend charging valve
Faema E61 legend charging valveReturn to the Faema E61 Legend water inlet parts overview
€13.71
Faema E61 filterholder gasket 8.5 mm
Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...
€3.38
Parker solenoid valve 2 ways base mounting 220/230V 50/60Hz 9W
Parker solenoid valve 2 ways base mounting 220/230V 50/60Hz 9WReturn to the Faema E61 Legend water inlet parts overview
€80.75
Faema E61 steam valve knob
On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...
€18.50
IMS Faema single cup filter basket 7/9 gr
The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. The single filterbasket on this page has the IMS product code B701TH26.5E This single filterbasket can hold ground coffee from 7 grams up to 9grams. The basket...
€25.59
Brewing group gigleur 0.6mm
Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines Return to the Faema E61 group parts overview
€1.58
Faema E61 complete steam valve
The steam and water valve on this page can be found on various old and new Faema models. The Faema part reference for this item is 903743000 This valve has on the steam/water tube side a female thread of 3/8” BSP-G. On the inlet side the thread is a male 3/8” BSP-G. This steam/water valve does not come with a knob. You can also use the original Bakelite...
€70.43
Faema E61 valve rod washer stainless
This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101 This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...
€0.74
Faema E61 gasket PTFE 22x16x2mm
The PTFE gasket on this page is used in a variety of E61 Style of brewing groups as well as the Faema E61 brewing group. You can find the gasket with brands such as La Pavoni, Faema, Wega, Grimac, Bezzera, La Scala, Vibiemme and Brasilia. The list of part and model references can be found in the extra info tab. This gasket has been made from PTFE. The...
€1.34
Portafilter gasket 73x57x9mm
Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.17
Faema E61 complete upper pipe
On this product page you will find the complete upper pipe for various E61 style and Faema E61 brewing groups. This item can be used in various E61 style brewing groups such as the ones used on the La Pavoni, Isomac and EC Heidelberg. But also on the Faema E61, Faema E61 Legend and the Faema E61 Jubilee espresso machines. The Faema part reference is...
€30.34
Faema E61 steam valve nut gasket 23x18x1mm
Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview
€0.82
Lucifer solenoid valve 2 way 1/8" 1/8" 24V AC 9W
The solenoid valve on this product page is one made by the company Lucifer. The coil states Parker, this is the main company. This solenoid valve is used in various La Cimbali and Faema espresso machines. This solenoid valve is a 2 way valve. The coil used is a 9W 24V model. The hole diameter is 2,5mm and is sealed off with a FKM seal. The maximum...
€104.03
O ring 3.69x1.78mm viton
O ring 3.69x1.78mm vitonReturn to the Faema E61 Legend water inlet parts overview
€0.52
Faema E61 valve gasket 13x4x4mm
The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...
€0.74
3 phase safety thermostat 169-18°
3 phase safety thermostat 169-18°. Suitable for:CodeProducer20300015 Astoria CMA56302101 Astoria CMA7434001 Bezzera95.01594 Carimali531-193-100 Cimbali02790035 Elektra3231133006 Faema3231135058 Faema531193100 FaemaA1400032 Fiorenzato C.s.0746906 Futurmat-Ariete07476906 Futurmat-Ariete10065832 Lavazza10067254...
€60.70
Faema E61 legend non return valve
Faema E61 legend non return valveReturn to the Faema E61 Legend water inlet parts overview
€18.56
Flex pipe 2000mm 3/8 ff conical base
On this page you will find a stainless steel water hose. This hose can be used to connect the water mains to your espresso machine any other suitable appliance. This stainless steel flex hose has a overall length of 2000mm and on each end a 3/8” BSP-G fitting. This connection is conical so there is no need to a gasket. The maximum fluid temperature which...
€18.50
Faema E61 valve gasket 15,5x7,5x4mm
This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...
€0.74
Faema E61 pump manometer
On this product page you will find a pump manometer suitable for the vintage Faema E61 but also for the modern Faema E61 Jubilee and the Faema E61 Legend espresso machines. The part reference for the Faema E61 Legend and Jubilee is 3781135801 This pressure gauge has a scale which goes from 0 – 16 bar of pressure. The body has a outer diameter of 52mm and...
€22.16
Faema E61 valve rod spring
This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.13