Nuova Simonelli heating element gasket 67x55x3mm

Rancilio flat gasket OR 18x12x3m

Solenoid valve connector. Suitable for:CodeProducer18110 Astoria CMAA10113 Astra000564 Aurora-brugnetti7631504 Bezzera00697.4.00.08 Brasilia7000/C Olab9007775 Reneka

The steam valve handle on this product page is a OEM/original Bezzera spare part. This item is used on the Bezzera Ellisse espresso machine. The Bezzera part reference numbers for this item are 5371810, 5373926, 5973021 and 5973022. This valve handle is made from a dark plastic.  On the inside is a knurled brass insert, which has a snug fit with the valve...

PTFE tap joint gasket 14.5x10.5x4.5mm

Lever ball bearing set for Faema Marte and Mercurio lever groups, only the early curved ones. For the later models Faema Mercurio you need to have a bigger bearing. click there.

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...

On this product page you will find a conical PTFE gasket suitable for a variety of La San Marco espresso machines. The La San Marco part reference for this item is 109049  The conical PTFE gasket has a outer diameter of 12,5mm a inner diameter of 7mm and a thickness of 5,5mm. This gasket seals off the Steam and water valve shaft off. This gasket has...

The spring on this page is one used in the flow regulation mechanism of the Faema Zodiac brewing group. The spring has been made out of stainless steel and has an outer diameter of 14mm and a overall length of 23mm. This item can be used in a variety of lever brewing groups made by Faema, but if you are not sure always send us a message to verify this.

Originally you would only find a boiler pressure manometer on the La Pavoni Professional espresso machines. This boiler pressure manometer is mounted on the top sight glass fitting. If you want to convert your La Pavoni Europiccola and fit it with a Pressure gauge, this is the kit you need The sight glass fittings used to have a internal diameter of...

La San Marco portafilter single spoutReturn to the portafilter overview

This item is the nut installed on the top of the piston shaft on various Gaggia lever espresso machines. With this you can fixate the bottom nut. This item is unfortunately out of production and won’t be made anymore.

The most common location for this to seal off the 3/8” male nut on the top of the Faema E61 and E61 style brewing groups like with Bezzera, Brasilia, Grimac, La Scala, Vibiemme and Wega.But also as a gasket to seal off boiler components with brands like Vibiemme and Grimac, This gasket has been made from the material AFM 34 made by the german company...

La Pavoni heating element gasket. 67x67 mm, int. hole dia 40mm, 3 holes

Astoria Wega tap joint spring

The piston shaft on a La Pavoni Home lever espresso machine. This shaft transfers the movement of the Lever on the brewing group (3954004) true the piston pins (3140463) to the piston shaft (312382 ). At the bottom of this piston shaft is of course the piston (314044) located. The item has a overall length of 111mm and M10 threads, this item is a original...

On this product page you will find a heating element which is really well suited to be installed in a Faema E61 2 group boiler. It runs on single phase and still gives enough power to power a 2 group E61. This heating element produces 2440/2900W at 220/240V the element has 4 wiring poles. In the middle of the heating element is also space for a heating...

On this page you will find a bottomless portafilter for Carimali espresso machines. Carimali, next to La San Marco uses 3 ears instead of the commonly found 2 ears. This portafilter can solely be used on Carimali brewing groups. The portafilter has 3 ear lugs instead of the traditional 2. And have a thickness of 6mm. The portafilter itself has been...

Is your la Pavoni Europiccola or Professional leaking from the pre-millennium brewing group? This basic gasket set might be handy. The set contains all the basic gaskets where a pre-millennium brewing group could leak on. The most common location of the brewing group are the piston gaskets. From using your machine too much, or just too little. Seen the...

Brass half nut 1/4" BSP-G  Return to our fitting overview

Faema la cimbali water inlet spring

Switch protective cover

On this page you will find a silicone sight glass gasket, with this seal there is a water tight seal between the glass and the body. This gasket can be used on the Elektra Microcasa lever espresso machine. This item has the Elektra part reference of 00119035 This silicone gasket has  a outer diameter of 15mm a inner diameter of 9mm and a thickness of 8mm.

This cam guide is vital in the lever mechanism used on the old Gaggia lever brewing groups. This cam guide is installed inside the side of the brewing group. The  lever cams do slide over this shaft. This item is not in production anymore.

Faema E61 brass washer 5.4x3mm is fitted between the gasket valve holder and between the valve guides Return to the Faema E61 group parts overview

For the La Pavoni pre-millennium brewing group you also need a portafilter gasket. In the case of a pre-millenium brewing group a standard o ring is used. This o ring has a internal diameter of 47mm and a cord thickness of 5,34mm so a outer diameter of 57,7mm. This portafilter gasket can be used in a variety of pre-millenium models like the La Pavoni...

La San Marco group supply springReturn to the  San Marco group parts overview

With the fitting on this page you can connect for instance 2 copper ¼” to each other or a solenoid valve to a tube. This fitting has on both sides a male ¼”BSP-G thread. This fitting has been manufactured in Italy out of brass.

Astoria Wega valve nut

Elektra microcasa sight glass 9x148mm

The flat copper gasket on this product page can be used with a variety of espresso machines and on various applications. You can use this copper gasket on espresso machines such as Marzocco, Casadio, ECM Heidelberg, La Scala, La Cimbali, Faema, Astoria, Wega, Nuova Simonelli, Wega and Rancilio. You will mainly see the use of this copper gasket to seal off...

Gicar level regulator RL30/1E/2C/F 115V

Arrarex Caravel heating element 1.0 - 1.3 version

La Pavoni showerReturn to the La Pavoni Bar modern parts overview

La Cimbali brewing group stainless steel ball Return to the La Cimbali lever parts overview