Faema E61 spare parts

The Faema E61: A Revolutionary Espresso Machine

The Faema E61 espresso machine is an iconic espresso machine with a timeless design that has revolutionized the espresso machine market. Introduced in the 1961, the Faema E61 marked a significant shift in the way espresso was made, setting new standards for quality and consistency in espresso extraction.

Faema Spare Parts - E61

Stainless steel pressure switch bracket

Pressure switch bracket made out of stainless steel 304. The bracket has a length of 90mm and a width of 18mm. This bracket is intended to fix one side to a boiler stud or inbetween a boiler bolt (up to M10).The other side is suitable to fit a pressure switch with a 1/4" BSP-G connector. 
€10.48

Faema E61 valve gasket 13x4x4mm

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...
€0.81

Faema E61 moustache set

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€31.71

Faema E61 complete steam valve

The steam and water valve on this page can be found on various old and new Faema models. The Faema part reference for this item is 903743000  This valve has on the steam/water tube side a female thread of 3/8” BSP-G. On the inlet side the thread is a male 3/8” BSP-G. This steam/water valve does not come with a knob. You can also use the original Bakelite...
€77.47

E61 group allen key copper washer 10x6,2x1mm

Almost every Faema e61 brewing group made has a Allen bolt on the front of the brewing group, yes there are models which don’t have this hole. This hole also needs to be sealed off. This can be done with PTFE tape. But you can also use a copper gasket for that. The Faema part reference for this item is 4054043102  This flat copper washer has a outer...
€0.60

Faema E61 inox filter 10.5x0.3mm

On this page you will find a small stainless steel water filter. This filter mesh goes into the top of the Faema E61 brewing groups. This filter membrane prevents clogging up of the nozzle in the group. The Faema part reference for this item is 4771135894.  This wire mesh membrane is made from stainless steel and has a outer diameter of 10,mm and a...
€1.82

Portafilter gasket 73x57x9mm red silicone

On this product page you will find a portafilter gasket, but not a standard one. This portafilter gasket has been made from food grade silicone, in the colour red.  This product has been made in Italy. The gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 9mm. You can use this on a variety of brands such as the Vibiemme...
€4.14

Faema E61 sticker 2 group

Faema E61 sticker 2 group for the glass plate on the back of the machine. Is your glass plate broken, we do also offer a new glass plate for this sticker. And to finish it off a new set of glass plate nuts Return to the Faema E61 body parts overview
€26.65

Faema E61 sleeve

The brass cam guide bushing shown on this page is used on the Faema E61 and E61 style brewing groups.  You can use this guide bushing on Faema, Grimac, Vibiemme, La Scala, Bezzera, Wega, Pavoni espresso machines. This brass bushing has a overall length of 28mm. The outer diameters are 10 and 15mm. The inner diameter is 8mm and the head thickness is 5mm....
€3.47

Faema E61 engine RPM 300W 230V

The espresso machine motor on this page is made by the Italian electric motor manufacturer RPM. This motor is intended to be used as a exterior motor, so that it isn’t installed inside the machine. The motor is a good motor to use with a vintage espresso machine like the Faema E61. Currently this coffee machine motor can be used on a variety of models...
€225.40

Asco pressure switch P302/6

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...
€81.48

Faema E61 gasket PTFE 22x16x2mm

The PTFE gasket on this page is used in a variety of E61 Style of brewing groups as well as the Faema E61 brewing group. You can find the gasket with brands such as La Pavoni, Faema, Wega, Grimac, Bezzera, La Scala, Vibiemme and Brasilia. The list of part and model references can be found in the extra info tab. This gasket has been made from PTFE. The...
€1.34

Faema filterbasket 21gr

The 2 coffee filterbasket on this page can be used a big variety of espresso machine brands. You can use this basket on brands such as Faema, Grimac, Astoria, Wega, Rancilio and Conti. This filterbasket has been made by the Italian company IMS Filtri. The IMS part reference is IMS3T011. Note: this is not a competition filterbasket. This stainless steel...
€6.22

Asco/Sirai pressure switch P303/T01 3 phase 20A

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€97.51

Faema E61 water level spring

The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...
€3.82

Faema E61 group infusion spring 14x45mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the top exhaust valve. When the lever is in the raised position this spring will keep the drain valve in the closed position. This stainless-steel compression spring has an outer diameter of 14mm. The length of...
€1.79

Faema E61 filterholder gasket 8.5 mm

Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...
€3.38

Faema E61 sight glass 12x175mm

The sight glass on this page is used on a variety of Lever espresso machines by the brand Faema. This sight glass can be used on models such as the Faema E61, Faema President and the Faema Lambro espresso machine. The sight glass has a outer diameter of 12mm and a overall length of 175mm. This sight glass has been made in Italy. The gasket you need for...
€5.74

IMS faema double cup filterbasket 18/22gr

The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. This double filterbasket on this page has the IMS product code B702TCH28.5E or B702TH28.5E This single filterbasket can hold ground coffee from 18 grams up to...
€25.03

Stainless ball 8mm

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...
€2.61

Portafilter gasket 73x57x9mm

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.59

Crushable copper washer 23x17x3mm

The crushable copper gasket on this page can be used with various applications on Brasilia espresso machines.  For instance, on sealing off steam and water tubes and as a gasket on various boiler fitting applications. The Brasilia part reference for this item is 01386.0.00.02  This copper gasket has a outer diameter of 23mm a inner diameter of 17mm and a...
€1.72

Faema E61 steam/water valve gasket holder

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...
€7.53

Faema E61 expansion valve spring

Faema E61 stainless steel expansion valve spring. This spring has a total length of 32.5mm and a external diameter of 15mm.This spring makes sure that the valve opens at the right over pressure. Return to the Faema E61 valve parts overview
€2.42

E61 style lever brewing group

On this product page you will find a complete E61 style brewing group. There are a variety of E61 style brewing groups. Examples of this are the Solenoid valve groups, with the solenoid valve at the bottom, or on the sides. This E61 style brewing group can be used on Fiorenzato, Grimac and La Scala espresso machines. The Fiorenzato part reference fort his...
€402.24

Faema E61 heating element gasket 57x43x3mm

On this page you will find a heating element gasket we had made out of AFM34 a food safe fibre material, made in Germany. This heating element gasket has a outer diameter of 57mm a inner diameter of 43mm and a thickness of 3mm. This heating element gasket can be used on a variety of heating elements such as the Faema E61, Faema E61 Legend, Faema E61...
€4.89

Faema E61 group net holder

This brass filter holder is used on the Faema E61 brewing group. This item has the Faema part reference of 4151135895. This brass filter holder slides over the nozzle in the op of the brewing group. In the widest section is the stainless steel filter placed with a brass ring on top of it. To keep the filter holder in place there is a nozzle spring...
€2.67

Faema E61 valve rod spring

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.24

Expansion valve 1/4M adjustable 10-14 Bar

The item on this page is a espresso machine expansion valve. This valve can be used on various espresso machine brands such as La Scala, La Spaziale, La San Marco, Faema and Brasilia. This expansion valve has a male thread which is ¼” BSP-G. This valve is adjustable. The pressure range goes from 10 to 14 bar. For the exhaust water there is a connection...
€28.03

History of the Faema E61

The Faema E61 was introduced in 1961 by the Italian espresso machine manufacturer Faema. It was designed by renowned engineer Ernesto Valente and quickly gained popularity for its innovative features and exceptional performance. One of the key innovations of the Faema E61 was its E61 brewing group, which replaced the traditional lever-operated espresso machines with a more efficient and consistent pump-operated system.

Technical Advancements

The Faema E61 brewing group introduced a number of technical advancements that set it apart from traditional espresso machines. One of the most notable features of the E61 group was its constant pump pressure of 9 bar, which ensured optimal extraction and consistency in every shot of espresso. This revolutionary design paved the way for a new generation of espresso machines and became the basis for many espresso machine manufacturers.

Our Selection of Faema E61 Spare Parts

At our store, we offer a wide selection of spare parts for the Faema E61 espresso machine. Whether you need boiler parts, steam/water valves, body parts, valve parts, brewing group parts, water level parts, pump parts, or water inlet parts, we have you covered. We stock a variety of genuine Faema E61 parts, ensuring that you can find exactly what you need to keep your espresso machine running smoothly.

Faema E61 Models

The Faema E61 espresso machine was produced in various configurations, ranging from 1-group to 6-group models. While the most common models are the 1-group, 2-group, and 3-group versions, there are also larger models available for high-volume commercial settings. Each model features the same innovative E61 brewing group, ensuring consistent performance and quality across the board.

Conclusion

The Faema E61 espresso machine is a true icon of the espresso world, known for its exceptional quality, timeless design, and groundbreaking innovation. With our selection of spare parts, you can keep your Faema E61 running smoothly for years to come, ensuring that you continue to enjoy delicious espresso beverages with every shot. If you have any questions or need assistance finding the right parts for your machine, don't hesitate to reach out to us. We're here to help you keep your Faema E61 in top condition.