Vibiemme Replica manual

Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview

This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...

In the Faema E61 and E61 style brewing groups you can find a variety of square valve pins, in different shapes and heights. This square pin screws into the M3 thread situation on the valve gasket holder. This model is one of the more common model which is used with brands such as Wega, Faema and La Pavoni. The part references are for Wega WY27421012,...

Vibiemme chromed lever sleeve

Ball valve 1/4M 1/4F

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...

Vibiemme brass lever rod

Expansion valve nipple

VBM e61 style rebuild kit

Parker solenoid valve 2 ways base mounting 220/230V 50/60Hz 9WReturn to the Faema E61 Legend water inlet parts overview

Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview

On this page you will find the o ring with the cord diameter of 1,9mm and a internal diameter of 7,2mm. This specific o ring is used with a variety of applications in expresso machines. For instance, with Expobar in the water inlet valve. For Faema in the cappuccinatore. With Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg and La Carimali in...

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...

Faema E61 brass washer 5.4x3mm is fitted between the gasket valve holder and between the valve guides Return to the Faema E61 group parts overview

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

Spring for steam valve

The drain valve is responsible for draining the last water out of the E61 style brewing group. This espresso machine part is made up out of 4 parts. The gasket holder, the gasket, small brass washer and a triangular valve rod. The total length of this part is 27mm. This drain valve used in a variety of espresso machine brands like: Expobar CTAV1-05,...

The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880  This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...

1/4" water charging valve autofill

When you have just used your steam wand to make a perfect latte. But you want to clean your steam wand, but you can’t because the metal is too hot. Don’t worry, we sell protective rubber sleeves which don’t pass on the heat so you won’t burn your hands. This specific model is suitable for a steam pipe which has a diameter of 10mm and has a length of 50mm....

Faema E61 brass small non return valve. This valve guide is sealed by this o ring and kept on it's place with the non return valve spring. Return to the Faema E61 valve parts overview

EPDM OR 4,47x1,78

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

Some heating elements have a triangular flange, these are used for some models of Vibiemme, Brasilia and Aurora Brugnetti. This heating element gasket is made from the fibre material AFM34 by Victor Reinz in Germany. This specific element has the outer dimensions of 80x80mm and a thickness of 2mm and is made from a fibre material. If you are not sure if...

The spring on this product page is used for various applications with various brands. This spring is used in water inlet systems, steam and water valves and non return valves. You will find this model of compression spring with brands such as Brasilia, La Spaziale, Faema, Grimac, Vibiemme and La Scala. This stainless steel compression spring has a outer...

If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...

If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...

On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...

Return to the Faema E61 valve parts overview

Vibiemme infusion valve 41.5mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the top exhaust valve. When the lever is in the raised position this spring will keep the drain valve in the closed position. This stainless-steel compression spring has an outer diameter of 14mm. The length of...

On this page you will find a brewing group spray nozzle. This nozzle is one of the most used spay nozzles used in the world of espresso machines. The nozzle has a outer diameter of 30mm and the male thread, which threads into the brewing group, is M10x1mm. What is the purpose of having a nozzle. Well the spray nozzle is located above the shower screen....

Faema E61 expansion valve gasket made out of nbr. This gasket makes sure that the expansion valve doesn't leak below the opening pressure of the valve. The gasket itself is seated in a valve guide which also has the function of spring guide for the expansion valve. Return to the Faema E61 valve parts overview