Vibiemme Replica manual

E61 style upper sleeve. not for faema e61

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the bottom exhaust valve. When the lever is in the lowest position the valve assembly will push this spring inward and the exhaust valve will open completely. This will make sure that all the exhaust water goes out...

On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

The item on this page is a gasket holder which is used in a variety of E61 brewing groups. You can find this item in some valve assemblies used on Faema, Pavoni and Wega espresso machines. For some brands this item is also used in the steam/water and water inlet valves. This brass gasket holder has 2 threads. 1 female and one male. The female thread is a...

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...

Vibiemme upper sleeve

If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...

The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880  This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...

VBM e61 style rebuild kit

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...

On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the top exhaust valve. When the lever is in the raised position this spring will keep the drain valve in the closed position. This stainless-steel compression spring has an outer diameter of 14mm. The length of...

On this page you will find a brass steam pipe bushing. But what is a pipe bushing. A pipe bushing makes it possible to move the steam and water wand freely without leaking. So how does it work? Well the pipe bushing has on the valve side 2 o rings, these seal against the side of the inside of the valve. But on the top ring of the pipe bushing there is...

Return to the Faema E61 valve parts overview

O ring 14x2mm

Locking group gasket

When you have just used your steam wand to make a perfect latte. But you want to clean your steam wand, but you can’t because the metal is too hot. Don’t worry, we sell protective rubber sleeves which don’t pass on the heat so you won’t burn your hands. This specific model is suitable for a steam pipe which has a diameter of 10mm and has a length of 50mm....

Vibiemme infusion valve 41.5mm

On this product page you will find a portafilter gasket suitable for a variety of antique Faema espresso machines. As well for the Faema Marte, Faema Mercurio, Faema E61. This portafilter gasket has a outer diameter of 72,5mm a inner diameter of 57mm and a thickness of 8mm. This gasket has been manufactured from NBR. As mentioned before you can use this...

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...

Spring for steam valve

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...

Some heating elements have a triangular flange, these are used for some models of Vibiemme, Brasilia and Aurora Brugnetti. This heating element gasket is made from the fibre material AFM34 by Victor Reinz in Germany. This specific element has the outer dimensions of 80x80mm and a thickness of 2mm and is made from a fibre material. If you are not sure if...

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...

In the Faema E61 and E61 style brewing groups you can find a variety of square valve pins, in different shapes and heights. This square pin screws into the M3 thread situation on the valve gasket holder. This model is one of the more common model which is used with brands such as Wega, Faema and La Pavoni. The part references are for Wega WY27421012,...

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...

Parker solenoid valve 2 ways base mounting 220/230V 50/60Hz 9WReturn to the Faema E61 Legend water inlet parts overview

With this steam valve you can clearly see that there are some resemblances between Faema and Vibiemme. Technically it is as good as identical as a e61 valve, the only difference is that the Vibiemme valve has a stainless-steel ball in the valve. Aesthetically the differences are that the chrome plated tap nut is a lot squarer then the original. And one of...

On this product page you will find a boiler pressure gauge suitable for a variety of Vibiemme espresso machines. The VBM part reference for this manometer is MANM49025GHIR. The pressure gauge can show a boiler pressure from 0 to 2,5bar. The body of the manometer is 49mm, the frame of the pressure gauge is 57mm. This manometer has a capillary with a female...