Faema E61 Legend

Faema E61 Legend parts

This page is dedicated to parts for the Faema E61 Legend. This machine was re-introduced around the turn of the century. The faema Legend was made 3 configurations:

·          Faema E61 Legend S1;

·          Faema E61 Legend S2;

·          Faema E61 Legend S3

Esthetically the Faema E61 looks quite a lot like the Faema E61 Legend espresso machine. But technically there are quite a lot off differences.

Water level, the water level used in the Faema E61 legend is one with a casted housing with a sight glass in front. This model is also used on a variety of Faema models like: Faema E92, Faema E97, Faema due and so on   And a variety of La Cimbali models like the La Cimbali M39 and the La Cimbali M39 GT

The pump and motor are nowadays installed inside the machine, traditionally the pump and motor on the Faema e61 could be found outside the machine.

On the Faema E61 legend you can now also find standard a autofill system. So the chance that your heating element will dry boil, because of the lack off water, also reduced a lot. The installation of a safety thermostat inside the element also reduced this a lot.

A other item which has been changed over the time. Is that the traditional mercury pressure switch has been replaced by a new model from Asco (this used to be Sirai)

If you have any questions about your Faema E61 legend espresso machine, don’t hesitate to contact us.

Faema E61 legend

Faema glass support set

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...
€45.30

E61 style group spout breaker

On this page you will find a brewing group spray nozzle. This nozzle is one of the most used spay nozzles used in the world of espresso machines. The nozzle has a outer diameter of 30mm and the male thread, which threads into the brewing group, is M10x1mm. What is the purpose of having a nozzle. Well the spray nozzle is located above the shower screen....
€6.37

Faema E61 filterbasket double 12gr

Stainless steel double filterbasket for a Faema E61 brewing group. This basket can contain 12grams of coffee. The width of the basket is 70mm and the height of the basket is 22mm.if you are looking for a single filterbasket click there. Return to the Faema E61 group parts overview
€6.46

3 phase safety thermostat 169-18°

3 phase safety thermostat 169-18°. Suitable for:CodeProducer20300015 Astoria CMA56302101 Astoria CMA7434001 Bezzera95.01594 Carimali531-193-100 Cimbali02790035 Elektra3231133006 Faema3231135058 Faema531193100 FaemaA1400032 Fiorenzato C.s.0746906 Futurmat-Ariete07476906 Futurmat-Ariete10065832 Lavazza10067254...
€60.70

Safety valve 3/8" 2.0 bar CE PED IV certified

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€10.47

Faema e61 rubber foots 25x6mm

It is quite common that the rubber feet of your Faema E61, Faema President, Faema E61 Legend or Faema E61 Jubile will break down. This can be due to age, cracking or just moving around. These rubber feet go in the bottom of the aluminium feet used on all these models, the modern adjustable feet have the part reference of 3515-135 857 and the fixed feet at...
€4.16

Portafilter gasket 73x57x9mm

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.17

Anti vacuum valve TV 1/4"

Anti vacuum valve TV 1/4". Suitable for:CodeProducerA10220 Astra000634 Aurora-brugnetti7452502 Bezzera05062.4.00.09 Brasilia01.00504 Carimali418-911-002 Cimbali418-911-010 Cimbali418911010 Cimbali408898 ContiC219900560 Ecm00200034 Elektra65000205 Expobar2161-118968 Faema2161118968 Faema418911002 Faema...
€9.60

Faema E61 steam valve knob

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...
€18.50

Portafilter gasket suplement 72x58x0.8mm

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...
€0.76

Faema E61 sleeve

The brass cam guide bushing shown on this page is used on the Faema E61 and E61 style brewing groups.  You can use this guide bushing on Faema, Grimac, Vibiemme, La Scala, Bezzera, Wega, Pavoni espresso machines. This brass bushing has a overall length of 28mm. The outer diameters are 10 and 15mm. The inner diameter is 8mm and the head thickness is 5mm....
€3.16

Faema E61 stainless steel valve rod

On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...
€13.15

Stainless ball 8mm

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...
€2.37

Faema E61 small square rod 6mm

On this product page you will find a key component for a Faema E61 and Wega E61 style brewing group. this square brass valve pin has the Faema part reference of 4161135916 and the Wega part reference of W10349. This small brass valve pin screws on top of a gasket holder. The square is 6x6mm. In the middle is a female M3 thread. This item has been made in...
€1.44

IMS Faema single cup filter basket 7/9 gr

The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. The single filterbasket on this page has the IMS product code B701TH26.5E This single filterbasket can hold ground coffee from 7 grams up to 9grams. The basket...
€25.59

IMS E61 style shower screen

This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....
€22.75

Faema E61 pump manometer

On this product page you will find a pump manometer suitable for the vintage Faema E61 but also for the modern Faema E61 Jubilee and the Faema E61 Legend espresso machines. The part reference for the Faema E61 Legend and Jubilee is 3781135801  This pressure gauge has a scale which goes from 0 – 16 bar of pressure. The body has a outer diameter of 52mm and...
€22.16

Faema E61 Legend and Jubilee front lower feet

These machine feet are used on the Faema E61 Legend and the Faema E61 Jubilee. They can be used on the front left as the front right feet, which have both the part number 3515-135 856. These feet do come with the rubber insert 4991-136 040 These feet are made from polished aluminium. The top section has a diameter of 35mm and the bottom section has a...
€55.37

E61 group allen key copper washer 10x6,2x1mm

Almost every Faema e61 brewing group made has a Allen bolt on the front of the brewing group, yes there are models which don’t have this hole. This hole also needs to be sealed off. This can be done with PTFE tape. But you can also use a copper gasket for that. The Faema part reference for this item is 4054043102  This flat copper washer has a outer...
€0.60

Faema E61 valve gasket 15,5x7,5x4mm

This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...
€0.74

Faema E61 PTFE gasket 26x21x2mm

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...
€1.38

Rubber pump motor connector 35mm

The item on this page is a rubber motor coupling. This coupling can be used on various Faema and Cimbali espresso machines. There are 2 types of couplings the 35mm and the 40mm coupling. This is the 35mm This coupling is used on the Faema E61 legend and Faema E61 Jubilee espresso machines, the 40mm coupling won’t fit this application. The Faema part...
€11.52

Faema front bakelite knob set

It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...
€36.70

Faema E61 camme holder

The cam holder shown on this page can be used on the Faema E61 and the Faema E61 Legend. The ones used on the E61 style brewing groups have a different shape. The Faema part reference for this item is 4152135911. This item has been machined from a solid piece of brass. After machining and polishing it has been nickel and chrome plated. This item has been...
€36.78

Faema E61 plug for camme holder

This stuffing nut is used to set even pressure on the gaskets of the cam shaft used in the E61 brewing groups. This nut can be used on the classical Faema E61 as well as the modern E61 style brewing groups. Such as Bezzera, La Scala, Grimac, Isomac, Pavoni, Brasilia and Vibiemme. This stuffing nut has been made from nickel and chrome plated brass. The...
€8.92

Faema E61 moustache set

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€28.82