Filter by
Filter

Faema E61 Jubilé

Faema E61 Jubilee spare parts

The Faema E61 legend and the Faema E61 jubilee are re-introduced around the turn of the century. The design was kept the same, but technically the machine was updated to with modern features. Like replacing the mercury switch with a modern Sirai pressure switch, temperature probe and with the newer machines a internal pump.

With the introduction of the Faema E61 jubilee lifted the traditional machine to a new level. This model is solenoid operated instead of with the manual valves like with the original Faema E61. Which is standard for a modern espresso machine.

In this overview you can find most parts for the Faema E61 legend and Faema E61 jubilee espresso machine. If you can't find the parts your looking for just send a email.

Faema E61 Jubilé spare parts

Faema E61 moustache set

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€31.71

Faema E61 plastic top 1 group

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...
€265.67

Faema E61 steam tube

The straight steam tube on this page can be used on a variety of Faema espresso machine models. This is a straight tube and can be bend into every shape you want, not too much off course This steam tube has been made from chrome plated copper. The fitting on the valve side is a 3/8” BSP-G thread and on the steam tip side is a 1/8” BSP-G thread. This steam...
€34.99

IMS Faema double cup filterbasket 12/18gr

A lot of the filterbasket sizes are quite standardized. This IMS filterbasket is good example of this. The basket is made by IMS filtra, but it is a competition basket and not from the standard IMS basket line.  The IMS part number for this double filterbasket is B702TH24.5M. The double filterbasket is made from stainless steel 304, food safe. The outer...
€28.03

Faema E61 glass plate srew set

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€54.91

3 phase safety thermostat 169-18°

3 phase safety thermostat 169-18°. Suitable for:CodeProducer20300015 Astoria CMA56302101 Astoria CMA7434001 Bezzera95.01594 Carimali531-193-100 Cimbali02790035 Elektra3231133006 Faema3231135058 Faema531193100 FaemaA1400032 Fiorenzato C.s.0746906 Futurmat-Ariete07476906 Futurmat-Ariete10065832 Lavazza10067254...
€66.77

Faema E61 group upper plug

The fitting on this page is the top fitting on almost every E61 brewing group. You can find the male stop on brands such as Vibiemme, La Scala, Bezzera, Grimac, Faema, La Pavoni, Wega and Brasilia espresso machines. This male cap has a diameter of 16mm. It has been made from brass and has been nickel and chrome plated. The thread used is a 3/8” BSP-G...
€5.65

Portafilter gasket suplement 72x58x0.8mm

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...
€0.84

Anti vacuum valve V.A.R. 1/4"

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€12.00

Faema E61 steam valve pin

The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880  This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...
€2.96

IMS Faema single cup filter basket 7/9 gr

The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. The single filterbasket on this page has the IMS product code B701TH26.5E This single filterbasket can hold ground coffee from 7 grams up to 9grams. The basket...
€25.59

Faema E61 inox filter 10.5x0.3mm

On this page you will find a small stainless steel water filter. This filter mesh goes into the top of the Faema E61 brewing groups. This filter membrane prevents clogging up of the nozzle in the group. The Faema part reference for this item is 4771135894.  This wire mesh membrane is made from stainless steel and has a outer diameter of 10,mm and a...
€1.82

Faema E61 group net holder

This brass filter holder is used on the Faema E61 brewing group. This item has the Faema part reference of 4151135895. This brass filter holder slides over the nozzle in the op of the brewing group. In the widest section is the stainless steel filter placed with a brass ring on top of it. To keep the filter holder in place there is a nozzle spring...
€2.67

Faema E61 gasket PTFE 22x16x2mm

The PTFE gasket on this page is used in a variety of E61 Style of brewing groups as well as the Faema E61 brewing group. You can find the gasket with brands such as La Pavoni, Faema, Wega, Grimac, Bezzera, La Scala, Vibiemme and Brasilia. The list of part and model references can be found in the extra info tab. This gasket has been made from PTFE. The...
€1.34

Faema E61 valve rod spring

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.24

Faema E61 Legend and Jubilee front lower feet

These machine feet are used on the Faema E61 Legend and the Faema E61 Jubilee. They can be used on the front left as the front right feet, which have both the part number 3515-135 856. These feet do come with the rubber insert 4991-136 040 These feet are made from polished aluminium. The top section has a diameter of 35mm and the bottom section has a...
€55.37

Faema E61 complete upper pipe

On this product page you will find the complete upper pipe for various E61 style and Faema E61 brewing groups. This item can be used in various E61 style brewing groups such as the ones used on the La Pavoni, Isomac and EC Heidelberg. But also on the Faema E61, Faema E61 Legend and the Faema E61 Jubilee espresso machines. The Faema part reference is...
€33.38

Faema E61 legend jubilee portafilter double

On this product page you will find a double portafilter which is suitable for the Faema E61 Legend and the Faema E61 Jubilé espresso machines. The part reference number for this item is 2771-135 803.The portafilter has 2 ears oriented at 90 degree. The ears have a thickness of 6,3mm. The spout connection on this portafilter is a 3/8” BSP-G thread. This...
€100.01

Faema E61 boiler manometer

This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...
€43.61

O ring 6.07x1.78mm Solenoid valve

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...
€0.67

E61 style groups shower without welding 60mm

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...
€3.32

Portafilter gasket 73x57x9mm

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.59