Filter by
Filter

Faema E61 Jubilé

Faema E61 Jubilee spare parts

The Faema E61 legend and the Faema E61 jubilee are re-introduced around the turn of the century. The design was kept the same, but technically the machine was updated to with modern features. Like replacing the mercury switch with a modern Sirai pressure switch, temperature probe and with the newer machines a internal pump.

With the introduction of the Faema E61 jubilee lifted the traditional machine to a new level. This model is solenoid operated instead of with the manual valves like with the original Faema E61. Which is standard for a modern espresso machine.

In this overview you can find most parts for the Faema E61 legend and Faema E61 jubilee espresso machine. If you can't find the parts your looking for just send a email.

Faema E61 Jubilé spare parts

Faema E61 steam valve pin

The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880  This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...
€2.96

Faema E61 steam valve knob

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...
€20.35

Faema front bakelite knob set

It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...
€40.37

Faema E61 moustache set

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...
€31.71

Portafilter gasket 73x57x9mm

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.59

Faema E61 filterbasket single 7gr

Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview
€5.26

Faema E61 plastic top 1 group

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...
€265.67

Level indicator red ball

This red ball is a level indicator ball. This ball floats inside the water level tube. Seen it’s not always easy to see the water level makes a floating red ball it a lot easier. There are more colours available with different diameter of balls. This red ball has a diameter of 5,8mm and is made in Italy. This type of level indicator can be found in a...
€2.40

Faema E61 group net holder

This brass filter holder is used on the Faema E61 brewing group. This item has the Faema part reference of 4151135895. This brass filter holder slides over the nozzle in the op of the brewing group. In the widest section is the stainless steel filter placed with a brass ring on top of it. To keep the filter holder in place there is a nozzle spring...
€2.67

Faema E61 steam/water group expanding spring

The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...
€2.48

Faema E61 complete steam valve

The steam and water valve on this page can be found on various old and new Faema models. The Faema part reference for this item is 903743000  This valve has on the steam/water tube side a female thread of 3/8” BSP-G. On the inlet side the thread is a male 3/8” BSP-G. This steam/water valve does not come with a knob. You can also use the original Bakelite...
€77.47

Faema E61 stainless steel valve rod

On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...
€14.47

IMS Faema double cup filterbasket 12/18gr

A lot of the filterbasket sizes are quite standardized. This IMS filterbasket is good example of this. The basket is made by IMS filtra, but it is a competition basket and not from the standard IMS basket line.  The IMS part number for this double filterbasket is B702TH24.5M. The double filterbasket is made from stainless steel 304, food safe. The outer...
€28.03

Safety valve 3/8" 2.0 bar CE PED IV certified

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€11.52

Washer 14x8x1mm brass

On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569  This brass flat washer has a outer diameter of...
€2.09

Faema E61 valve rod spring

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.24

Brewing group gigleur 0.6mm

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview
€1.74

Faema E61 group upper plug

The fitting on this page is the top fitting on almost every E61 brewing group. You can find the male stop on brands such as Vibiemme, La Scala, Bezzera, Grimac, Faema, La Pavoni, Wega and Brasilia espresso machines. This male cap has a diameter of 16mm. It has been made from brass and has been nickel and chrome plated. The thread used is a 3/8” BSP-G...
€5.65

Anti vacuum valve TV 1/4"

Anti vacuum valve TV 1/4". Suitable for:CodeProducerA10220 Astra000634 Aurora-brugnetti7452502 Bezzera05062.4.00.09 Brasilia01.00504 Carimali418-911-002 Cimbali418-911-010 Cimbali418911010 Cimbali408898 ContiC219900560 Ecm00200034 Elektra65000205 Expobar2161-118968 Faema2161118968 Faema418911002 Faema...
€10.56

Flex pipe 2000mm 3/8 ff conical base

On this page you will find a stainless steel water hose. This hose can be used to connect the water mains to your espresso machine any other suitable appliance. This stainless steel flex hose has a overall length of 2000mm and on each end a 3/8” BSP-G fitting. This connection is conical so there is no need to a gasket. The maximum fluid temperature which...
€20.35

Faema E61 inox filter 10.5x0.3mm

On this page you will find a small stainless steel water filter. This filter mesh goes into the top of the Faema E61 brewing groups. This filter membrane prevents clogging up of the nozzle in the group. The Faema part reference for this item is 4771135894.  This wire mesh membrane is made from stainless steel and has a outer diameter of 10,mm and a...
€1.82

IMS E61 style shower screen

This shower screen style is one of the most used shower screens with espresso machines. It can be for instance used on the Faema E61 and E61 style brewing groups. This specific model of shower screen is made by IMS Filtri in Italy. But this is not a standard version, it is from their Competition series shower screens. This specific model is the E61200IM....
€25.03