Filter by
Filter

Faema President

Our selection of Faema President spare parts

Faema Spare Parts - President

Faema E61 valve rod washer stainless

This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101  This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...
€0.81

Faema E61 flange heating element side 12 holes

With machines which are around 60 years old it is not uncommon that you get corrosion in some parts. With the Flanges used on the Faema E61, Faema President and the Faema Lambro it is quite common to find pin holes. These holes leak air or water in some cases. This flange has been made for the heating element side of the Faema E61/President and Lambro...
€455.77

Portafilter gasket suplement 72x58x0.8mm

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...
€0.84

Faema E61 heating element 1 group 1500W 230V

The element on this product page is ideal for your antique lever espresso machine, or Faema E61 espresso machine. This heating element has the typical Faema type of brass flange. The element is powered at 230V and supplies 1500W. The immersed length of the element is just 145mm. The heating element gasket used for this element has a outer diameter of 57mm...
€102.48

Faema spring 14x23mm

The spring on this page is one used in the flow regulation mechanism of the Faema Zodiac brewing group. The spring has been made out of stainless steel and has an outer diameter of 14mm and a overall length of 23mm. This item can be used in a variety of lever brewing groups made by Faema, but if you are not sure always send us a message to verify this.
€4.97

Lever V piston gasket 51x38x7.5mm

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio, Faema and Aurora Brugnetti Lever groups. The outer diameter of this piston gasket is 51mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio...
€3.60

faema PTFE gasket 15x10x2.5

On the back of the Faema Zodiac brewing group is a top nut and a bottom nut. The top nut needs to be sealed off. Otherwise the water will leak out of it. You would have the choice of a fibre gasket but also a PTFE gasket. On this page you will find the PTFE gasket. The dimensions of this PTFE gasket measure a outer dimension of 15mm a inner dimension of...
€3.28

Faema Aluminium group head

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...
€322.51

Faema E61 heating element 3 group 3700W 230V

The heating element shown on this page is suitable for various 3 group Faema espresso machine models such as the Faema E61, Faema President and the Faema Urania. This element produces at 220V 3700W. There are 4 connecting poles. The immersed length of the element is 455mm. The flange is a typical Faema style flange of 95x57mm. In the middle of the flange...
€94.05

Asco/Sirai pressure switch P303/T01 3 phase 20A

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€97.51

Faema E61 PTFE gasket 26x21x2mm

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...
€1.52

Faema E61 water level gasket 21x11.4x5mm

The sight glass gasket on this page is used in a variety of older Faema espresso machines such as the Faema E61, Faema President and Faema Lambro. This gasket has been made from EPDM. The outer diameter of this gasket is 21mm the inner diameter is 11,5mm and the thickness is 5mm. This gasket has been made in Germany.
€1.52

Asco pressure switch P302/6

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...
€81.48

Faema E61 plastic top 2 group

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 2 group are only the measurements of the width and length of the U shape. The length of this plexi is about 455 and the width is 220mm. This plexiglass...
€325.64

Faema lever group ball bearing set

All the Faema Lever brewing groups use ball bearings to function properly, they are not all the same btw. The ball bearing set on this page is suitable for the Faema President, Faema Urania, Faema Lambro, Faema Mercurio (with the zodiac type group) and the Faema Zodiac group type. The Faema Marte and first series of the Faema Mercurio use a different...
€17.66

Faema E61 valve rod spring

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.24

Lever group fibre gasket 22x17x2mm

On this product page you will find a fibre gasket used on the Faema Zodiac lever brewing group. This gasket seals off the flow regulator on multiple locations. This fibre gasket has a outer diameter of 22mm a inner diameter of 17mm and a thickness of 2 mm. this item has been made in Italy. You can use this gasket on the flow regulators used on the later...
€2.54

Anti vacuum valve V.A.R. 1/4"

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€12.00

Faema E61 glass plate srew set

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€54.91

Faema lever fork

Is the lever fork on your Faema Lever group worm out, this is the solution for it. When you have a aluminium lever fork or brass one where there is slack on the lever pint, it is time to replace it. The item on this page is a brass casted and chrome plated lever fork for the Faema lever brewing groups, of course not for all models. You can use this model...
€106.25

Faema E61 sight glass 12x175mm

The sight glass on this page is used on a variety of Lever espresso machines by the brand Faema. This sight glass can be used on models such as the Faema E61, Faema President and the Faema Lambro espresso machine. The sight glass has a outer diameter of 12mm and a overall length of 175mm. This sight glass has been made in Italy. The gasket you need for...
€5.74

Faema lever group spring 46mmx169mm

The compression spring on this page can be used in various Lever espresso machines. But to start: Always check the dimensions of your original spring. The product on this page has a overall length of 169mm and a outer diameter of 46mm. The compression spring is made from spring steel and has been galvanized. This compression spring can be used on a...
€17.21

Faema E61 steam tube

The straight steam tube on this page can be used on a variety of Faema espresso machine models. This is a straight tube and can be bend into every shape you want, not too much off course This steam tube has been made from chrome plated copper. The fitting on the valve side is a 3/8” BSP-G thread and on the steam tip side is a 1/8” BSP-G thread. This steam...
€34.99

Faema E61 water level spring

The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...
€3.82

Faema E61 plastic top 1 group

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...
€265.67

Faema E61 water inlet valve guide

Faema E61 brass water inlet valve guide. You can use this valve guide for several faema models. But they are mostly used on the Faema E61. comes with the gasket Return to the Faema E61 water inlet overview
€35.73

Faema lever group back rubber bumper

On this page you will find the Faema lever back bumper. This rubber piece dampens the return of the lever into it’s resting position. Over time this rubber get’s damages or perishes. You can use this bumper on all Faema lever brewing groups like the ones on the Faema Marte, Faema Mercurio, Faema Zodiac, Faema President, Faema Urania and the Faema Lambro.
€4.14

Faema bottomless portafilter

The bottomless portafilter on this page can be used on a variety of Faema espresso machines. This bottomless portafilter can be used on the antique lever espresso machines as well on the E61 brewing groups. This bottomless portafilter comes with a standard style of handle. The ear orientation is at 90 degrees. The thickness off the ears is 7,2mm. This...
€66.43

Faema E61 and president 1 group glass

On this product page you will find a replacement glass for a Faema E61 1 group and a Faema President 1 group lever espresso machine. The outer dimensions of the glass are 365mm by 165mm The distance between the holes is not identical horizontally. Vertically the distance it is about 85mm from centre to centre. For the horizontal distance, centre to centre...
€234.10

Faema E61 valve gasket 13x4x4mm

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...
€0.81

Faema aluminium lever cover

On this page you will find the aluminium lever group cover used in a variety of Faema Lever brewing groups. What is the purpose of this item? Mainly esthetical. But it also prevents dust getting in the brewing group mechanism and the chance also reduces that someone get’s its finger stuck in the bearing mechanism. On what kind of lever brewing groups can...
€73.45

Faema piston shaft

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...
€103.85

Faema e61 rubber foots 25x6mm

It is quite common that the rubber feet of your Faema E61, Faema President, Faema E61 Legend or Faema E61 Jubile will break down. This can be due to age, cracking or just moving around. These rubber feet go in the bottom of the aluminium feet used on all these models, the modern adjustable feet have the part reference of 3515-135 857 and the fixed feet at...
€4.16