Faema President

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...

The sight glass gasket on this page is used in a variety of older Faema espresso machines such as the Faema E61, Faema President and Faema Lambro. This gasket has been made from EPDM. The outer diameter of this gasket is 21mm the inner diameter is 11,5mm and the thickness is 5mm. This gasket has been made in Germany.

This autolevel set contains the folowing parts:autofill device 230V; solenoid valve 1/8"  230V; level probe 140 mm; solenoid valve plastic cover; wiring harness; ball valve 1/8"

Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...

Pressure switch bracket made out of stainless steel 304. The bracket has a length of 90mm and a width of 18mm. This bracket is intended to fix one side to a boiler stud or inbetween a boiler bolt (up to M10).The other side is suitable to fit a pressure switch with a 1/4" BSP-G connector. 

Faema lever group front stop. This stop makes sure that the lever assembly doesn't touch the brewing group when the lever is lowered. Over time the rubber used perishes or get’s damages. You can use this part on the Faema Zodiac lever group, Faema President, Faema Urania, Faema Lambro lever brewing groups. They are also usable for the Faema Marte and...

On the back of the Faema Zodiac brewing group is a top nut and a bottom nut. The top nut needs to be sealed off. Otherwise the water will leak out of it. You would have the choice of a fibre gasket but also a PTFE gasket. On this page you will find the PTFE gasket. The dimensions of this PTFE gasket measure a outer dimension of 15mm a inner dimension of...

The spring on this page is a water level spring and is being used on a variety of older Faema espresso machines. It can be used on espresso machine models as the Faema E61, Faema President and the Faema Lambro. This stainless steel spring has a outer diameter of 22mm and a height of 20mm. Note: this item is not suitable for the Faema E61 legend and the...

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...

Have you ever wanted to convert your single group Faema lever espresso machine from a 220-230V version to a 110V version, now you can. The heating element on this product page is suitable for installation on various antique Faema Lever groups and regular Faema E61 groups. This heating element has the typical Faema type of brass flange. The element is...

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

On this product page you will find a replacement glass for a Faema E61 1 group and a Faema President 1 group lever espresso machine. The outer dimensions of the glass are 365mm by 165mm The distance between the holes is not identical horizontally. Vertically the distance it is about 85mm from centre to centre. For the horizontal distance, centre to centre...

The straight steam tube on this page can be used on a variety of Faema espresso machine models. This is a straight tube and can be bend into every shape you want, not too much off course This steam tube has been made from chrome plated copper. The fitting on the valve side is a 3/8” BSP-G thread and on the steam tip side is a 1/8” BSP-G thread. This steam...

Faema retention valve body Return to the Faema Zodiac lever parts overview

Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview

Is the lever fork on your Faema Lever group worm out, this is the solution for it. When you have a aluminium lever fork or brass one where there is slack on the lever pint, it is time to replace it. The item on this page is a brass casted and chrome plated lever fork for the Faema lever brewing groups, of course not for all models. You can use this model...

On this page you will find a piston gasket suitable for multiple espresso machine models. You can find this piston gasket on Rancilio, Faema and Aurora Brugnetti Lever groups. The outer diameter of this piston gasket is 51mm, the inner diameter is 38mm and the thickness of the gasket is 7,5mm. On Rancilio espresso machines you can use them on the Rancilio...

Faema E61 filterholder gasket 8.5mm nbr. The middle size portafilter gasket available for the E61 brewing group. There are 3 thickness sizes available for the E61:8mm; 8,5mm; 9mm.If your portafilter doesn't fit as you want, there are always thinner shims available to add to the gaskets:0,5mm; 0,8mm.It's always handy to purchase some gaskets extra,...

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

This gasket has been made from the fibre material AFM 34 in Germany. This gasket has a outer diameter of 26mm a inner of 21 and a thickness of 2mm. This gasket is used in a variety of components throughout a espresso machine. The most common place where this coffee machine gasket is used, is in the Faema E61, Faema E61 legend and E61 style brewing groups....

With machines which are around 60 years old it is not uncommon that you get corrosion in some parts. With the Flanges used on the Faema E61, Faema President and the Faema Lambro it is quite common to find pin holes. These holes leak air or water in some cases. This flange has been made for the heating element side of the Faema E61/President and Lambro...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 2 group are only the measurements of the width and length of the U shape. The length of this plexi is about 455 and the width is 220mm. This plexiglass...

It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...

Stainless steel double filterbasket for a Faema E61 brewing group. This basket can contain 12grams of coffee. The width of the basket is 70mm and the height of the basket is 22mm.if you are looking for a single filterbasket click there. Return to the Faema E61 group parts overview

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...

All the Faema Lever brewing groups use ball bearings to function properly, they are not all the same btw. The ball bearing set on this page is suitable for the Faema President, Faema Urania, Faema Lambro, Faema Mercurio (with the zodiac type group) and the Faema Zodiac group type. The Faema Marte and first series of the Faema Mercurio use a different...

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

On this product page you will find a portafilter gasket, but not a standard one. This portafilter gasket has been made from food grade silicone, in the colour red.  This product has been made in Italy. The gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 9mm. You can use this on a variety of brands such as the Vibiemme...

Faema guide ring Return to the Faema Zodiac lever parts overview

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

On this product page you will find a boiler gasket for some of the Faema E61, Faema President and Faema Lambro espresso machines. This gasket goes in combination with the boilers which have a separate heating element flange and a water level flange or a single boiler with a heating element flange. We have this gasket made from AFM34 in Germany. This...