Faema E61 spare parts

The Faema E61: A Revolutionary Espresso Machine

The Faema E61 espresso machine is an iconic espresso machine with a timeless design that has revolutionized the espresso machine market. Introduced in the 1961, the Faema E61 marked a significant shift in the way espresso was made, setting new standards for quality and consistency in espresso extraction.

Faema Spare Parts - E61

E61 valve guide 12mm

In the Faema E61 and E61 style brewing groups you can find a variety of square valve pins, in different shapes and heights. This square pin screws into the M3 thread situation on the valve gasket holder. This model is one of the more common model which is used with brands such as Wega, Faema and La Pavoni. The part references are for Wega WY27421012,...
€1.58

Faema President and E61 2 group glass

It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...
€276.34

Faema E61 flange level side

Faema E61 flange sight glass side. Do you have a small leak in one of your boiler flanges. this can be fixed easily by replacing the flange which is leaking. Next to the level side flange we also offer the heating element side flange. Return to the Faema E61 boiler parts overview
€367.22

Anti vacuum valve V.A.R. 1/4"

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€10.91

Faema E61 lever knob

The handle knob on this page can be used on Faema E61 brewing groups. This handle goes on the brewing group control lever. Originally these were made from Bakelite, but nowadays that isn’t made that much anymore. The Faema part reference fort his item is 4741135910  This plastic lever brewing group handle is made from a shiny plastic. In the middle is a...
€12.04

Faema E61 small square rod 6mm

On this product page you will find a key component for a Faema E61 and Wega E61 style brewing group. this square brass valve pin has the Faema part reference of 4161135916 and the Wega part reference of W10349. This small brass valve pin screws on top of a gasket holder. The square is 6x6mm. In the middle is a female M3 thread. This item has been made in...
€1.44

Portafilter gasket suplement 72x58x0.8mm

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...
€0.76

Faema E61 expansion valve 3/8

Faema E61 expansion valve 3/8" BSP-G. This complete valve is made in the same style as the original expansion valve. The valve consists of the following components:Faema E61 Expansion Valve Nipple; Faema E61 Expansion Valve Guide; Faema E61 Expansion Valve Gasket; Faema E61 Expansion Valve SpringReturn to the Faema E61 valve parts overview
€46.08

Boiler top fitting 1/2"

If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...
€19.03

Faema E61 sticker 2 group

Faema E61 sticker 2 group for the glass plate on the back of the machine. Is your glass plate broken, we do also offer a new glass plate for this sticker. And to finish it off a new set of glass plate nuts Return to the Faema E61 body parts overview
€24.23

Asco/Sirai pressure switch P303/T01 3 phase 20A

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€88.64

Faema E61 glass plate srew set

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...
€49.92

Faema E61 group valve guide 11mm

The brass square pin on this page can be used on the Faema E61 groups and on the Wega E61 style of brewing groups. The Faema part reference for this item is 4161135915 and the Wega part references are W10341 and WY27421013. This square brass pin has a overall length of 11mm. The length and width are 6x6mm. on the inside is a female M3 thread. This square...
€1.83

Faema E61 inox filter 10.5x0.3mm

On this page you will find a small stainless steel water filter. This filter mesh goes into the top of the Faema E61 brewing groups. This filter membrane prevents clogging up of the nozzle in the group. The Faema part reference for this item is 4771135894.  This wire mesh membrane is made from stainless steel and has a outer diameter of 10,mm and a...
€1.66

Faema E61 brass camme lever rod

The item shown on this page is a cam shaft which is used on the Faema E61 and various other E61 style of brewing groups.  Such as Bezzera and La Pavoni e61 style groups. The Faema part reference for this item 3161136650, the Bezzera part reference is 7479950 and for La Pavoni the reference is 314077. This brass cam shaft has a overall length of 82mm. The...
€18.27

Faema o ring 7,2X1,9mm nbr

On this page you will find the o ring with the cord diameter of 1,9mm and a internal diameter of 7,2mm. This specific o ring is used with a variety of applications in expresso machines. For instance, with Expobar in the water inlet valve. For Faema in the cappuccinatore. With Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg and La Carimali in...
€0.56

Faema E61 stainless steel valve rod

On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...
€13.15

Stainless steel pressure switch bracket

Pressure switch bracket made out of stainless steel 304. The bracket has a length of 90mm and a width of 18mm. This bracket is intended to fix one side to a boiler stud or inbetween a boiler bolt (up to M10).The other side is suitable to fit a pressure switch with a 1/4" BSP-G connector. 
€10.48

Faema E61 group infusion spring 14x45mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the top exhaust valve. When the lever is in the raised position this spring will keep the drain valve in the closed position. This stainless-steel compression spring has an outer diameter of 14mm. The length of...
€1.62

Bottom fitting for boiler pipe 1/2"M 1/2"M, hole 1/4"F

If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...
€17.11

Brewing group gigleur 0.6mm

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview
€1.58

Flex pipe 1500mm 3/8 FF conical base

The flexible tube on this page has a overall length of 1500mm. This includes the fittings. The fittings on this pipe are female 3/8” BSP-G and both have a conical base, so there is no gasket needed. The tubes are rated up to 10 bar and with a maximum working temperature of 90 degree Celsius.
€17.11

Faema E61 stickers

On this page you will find the stickers which go on the front panel of the vintage Faema E61 and Faema President lever group. These can get damaged or not present at all. This set contains the Faema water level sticker descriptions, Massimo and Minimo. For the steam valve Vapore, for the water valve Scarico acqua. For the cup warmer valve the Scaldatazze....
€10.06

Expansion valve 1/4M adjustable 10-14 Bar

The item on this page is a espresso machine expansion valve. This valve can be used on various espresso machine brands such as La Scala, La Spaziale, La San Marco, Faema and Brasilia. This expansion valve has a male thread which is ¼” BSP-G. This valve is adjustable. The pressure range goes from 10 to 14 bar. For the exhaust water there is a connection...
€25.48

Faema E61 microswitch 16A 250V

On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...
€41.19

Compression spring 13x42mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This is the spring located in the upper section of the brewing group, in the trumpet/mushroom. This stainless-steel compression spring has a outer diameter of 13mm. The length of this compression spring is 42mm. This spring has been made in Italy. This...
€2.02

Faema E61 camme spring 15x25mm

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used at the cam shaft. This spring is compressed in the cam shaft assembly. Due to this compression the cam shaft gaskets will always seal off the shaft. This stainless-steel compression spring has a outer diameter of 15mm. The length of this...
€1.52

Faema E61 valve rod spring

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.13

Faema front bakelite knob set

It is quite common that on your old Faema E61 or Faema President the Bakelite body panel screws are missing or are broken. What do these body panel screws do? The back of the machine is slid on the front of the machine. There are 4 threads which go to the front plate of the Faema E61 and Faema President. On those 4 threads you can screw these Bakelite...
€36.70

Washer 14x8x1mm brass

On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569  This brass flat washer has a outer diameter of...
€1.90

History of the Faema E61

The Faema E61 was introduced in 1961 by the Italian espresso machine manufacturer Faema. It was designed by renowned engineer Ernesto Valente and quickly gained popularity for its innovative features and exceptional performance. One of the key innovations of the Faema E61 was its E61 brewing group, which replaced the traditional lever-operated espresso machines with a more efficient and consistent pump-operated system.

Technical Advancements

The Faema E61 brewing group introduced a number of technical advancements that set it apart from traditional espresso machines. One of the most notable features of the E61 group was its constant pump pressure of 9 bar, which ensured optimal extraction and consistency in every shot of espresso. This revolutionary design paved the way for a new generation of espresso machines and became the basis for many espresso machine manufacturers.

Our Selection of Faema E61 Spare Parts

At our store, we offer a wide selection of spare parts for the Faema E61 espresso machine. Whether you need boiler parts, steam/water valves, body parts, valve parts, brewing group parts, water level parts, pump parts, or water inlet parts, we have you covered. We stock a variety of genuine Faema E61 parts, ensuring that you can find exactly what you need to keep your espresso machine running smoothly.

Faema E61 Models

The Faema E61 espresso machine was produced in various configurations, ranging from 1-group to 6-group models. While the most common models are the 1-group, 2-group, and 3-group versions, there are also larger models available for high-volume commercial settings. Each model features the same innovative E61 brewing group, ensuring consistent performance and quality across the board.

Conclusion

The Faema E61 espresso machine is a true icon of the espresso world, known for its exceptional quality, timeless design, and groundbreaking innovation. With our selection of spare parts, you can keep your Faema E61 running smoothly for years to come, ensuring that you continue to enjoy delicious espresso beverages with every shot. If you have any questions or need assistance finding the right parts for your machine, don't hesitate to reach out to us. We're here to help you keep your Faema E61 in top condition.