Brasilia Portofino leva

On this page you will find a chrome plated lever group fork for various lever groups. This fork is responsible for transitioning the lever motion to a vertical motion. This chrome plated group fork can’t be used on the older AL lever groups as used by Astoria and Wega. That part is out of production. This specific item is OEM/Original item suitable for...

The item on this page is a steam and water valve washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item is 12153.0.00.03. This washer is made from machined brass. the outer diameter is 10,7mm, the inner diameter is 8,2mm and the thickness is 2mm. this washer is made in Italy. You can use this brass washer on...

The o ring on this product page is used on various Brasilia steam and water valves on various models. The Brasilia part references for this item are 05825.0.00.02 and 0582500002. This o ring is made from EPDM. The cord diameter is 2,62mm and the internal diameter is 25,07mm. This o ring is made in Italy.  You can use this o ring on the Brasilia Century,...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

Rancilio steam/water valve joint o ring 12,1x2,7mm

Gudgeon pin lever group

On this page you will find a portafilter gasket specially suited for lever espresso machine brewing groups. This specific portafilter gasket is suitable for brands such as the Astoria, Pavoni, Wega, Victoria Arduino, Fiorenzato and Brasilia lever groups. (seen they are the same model of group) This specific gasket has been made from NBR. This gasket has a...

The item on this product page is a steam and water valve screw, used on various Brasilia espresso machines. The Brasilia part reference number for this item 00107.4.00.04  This articulating valve screw is used in combination with the spring washers and the conical PTFE gaskets to seal off the valve. This item has been made in Italy. You can use these...

Conical portafilter gasket 66x56x6mm

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...

On this page you will find a OEM/Original shock absorber for the Astoria and Wega lever brewing groups. This absorber is located inside the lever fork. So when the lever is released by accident this rubber shock absorber will absorb some of the force. This absorber is also used when the lever is in rest position This shock absorber can be used on the...

On this product page you will find the connection between the lever and the lever group itself. In the top of this casted item you will screw the lever itself.  There are 2 holes. 1 of them has a bushing inside so that there is some axial movement possible. In the fixed hole goes the bearing shaft. In the movable hole goes a pin to make a connection with...

The gasket on this page is made from copper instead from PTFE or a fibre material. The copper gasket is mainly used on Rancilio espresso machines. The Rancilio part number for this item is 27400001. This copper gasket is from the flat type, so not a copper compression gasket. The outer diameter of this gasket is 24mm, the inner diameter is 21mm and the...

On this page you will find the front stop for various lever brewing groups. This front stop make sure tha you don’t damage the lever nor the castings of the brewing group itself. This rubber front stop can be used with brands such as Brasilia with part number 01432.0.00.02 , La Pavoni 477021 and Victoria Arduino 17000018 . For La Pavoni it is only...

Brass lever valve with PTFE lining

The crushable copper gasket on this page can be used with various applications on Brasilia espresso machines.  For instance, on sealing off steam and water tubes and as a gasket on various boiler fitting applications. The Brasilia part reference for this item is 01386.0.00.02  This copper gasket has a outer diameter of 23mm a inner diameter of 17mm and a...

On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...

One of the most universal items. The male brass plug. The plus on this page can be found in the catalogue of a variety of espresso machine manufacturers like Astoria, Faema, La Spaziale and Wega. This specific plug has a male ¼”BSP-G thread. The height of this plug is 13 mm and the wrench size for this plug is 17mm.

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

The steam pipe spring on this page is suitable for a variety of espresso machine brands, it’s also a universal item. This spring make sure that you can leave your steam tube in a fixed position. If there is no spring, it will fall back to the lowest point. This spring has a external diameter of 12mm and a overall length of 15mm and is made from stainless...

Astroia CMA style complete lever brewing group

Brasilia portafilter single spout Return to the portafilter  overview

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

This Conical PTFE gasket can be used on a variety of Brasilia espresso machines. For this item there is a Brasilia part reference of 00810.0.00.02. This gasket has a conical shape. The outer diameter of this PTFE gasket is 14,5mm, the inner diameter is 10mm and the thickness is 5mm. This gasket can be used on the rubber as well as on the ceramic valves....

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The lower o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 56,75mm. This specific o...

The item on this product page is a steam and water valve elastic washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item 01286.0.00.03  These washers are used in a pair in combination with the articulating valve screw, which is used on the steam and water valves. You can use these washers on the Brasilia...

Brasilia portofino/gradisca handle

Safety valve 1/2"1,8 Certif CE PED IV

The sight glass on this page can be used on various Vibiemme espresso machine models. The Vibiemme part reference for this item is MATECVELI140  This sight glass has a outer diameter of 11mm and a overall length of 140mm. this sight glass has silk printing on the glass. There is on the back a red line and on the front the lettering of max and min. This...

On this page you will find a heating element suitable for various Brasilia espresso machine models. This specific heating element is suitable for a 1 group espresso machine. The Brasilia part reference is 00614.2.00.08 This heating element produces 1800W at 230V, there are 4 connecting poles. The element has a immersed length of 170mm. The flange on this...

On this page you will find the o ring with the cord diameter of 1,9mm and a internal diameter of 7,2mm. This specific o ring is used with a variety of applications in expresso machines. For instance, with Expobar in the water inlet valve. For Faema in the cappuccinatore. With Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg and La Carimali in...

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

The water level fitting on this page can be used on various Brasilia espresso machine models. The Brasilia part reference number for this item are 00024.0.00.04 and 00024.0.00.04  This casted brass sight glass fitting has on the machine side a male 3/8” BSP-G thread, on water level side a female 3/8” BSP-G and on the bottom/top a female ¼” BSP-G thread....

This steam pipe bushing is a important element in the sealing and functioning of a steam and water valve. This bushing is pushed down on one side with a spring, this bushing has on the other side a hollow shape so that the ball of the steam and water valve can slide smoothly over the brass. This brass bushing has multiple dimensions. The external diameter...

On this product page you will find the injector tube for various lever espresso machine groups. For example used on Astoria, Wega and La Pavoni groups. This item is a OEM/original Astoria/Wega spare part, but can be used with La Pavoni brewing groups. The overall length of this tube is 140mm and the tube has a outer diameter of 12mm. the fittings screws...