Boiler injector and fitting 1/4" M-M
Boiler injector and fitting 1/4" M-M with 90° L=140MM Suitable for BFC, Grimac, La Scala Vibiemme
€19.18
0
My cart
Faema E61 spare parts
Boiler top fitting 1/2"
If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...
€20.93
Asco/Sirai pressure switch P303/T01 3 phase 20A
On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€97.51
Faema E61 group spout breaker
The item shown on this page is the last item on a Faema E61 brewing group, as well on some other e61 style brewing groups. This is the drain fitting which is all the way on the bottom of the brewing group. This model of drain can be used on the brands Faema, Grimac, Pavoni and Wega espresso machines. The Faema part reference for this item is 4152135921,...
€10.24
Faema E61 square shaft 34mm
On this page you will find a square brass pin. This brass pin is only used in the Faema E61 brewing group. There is no part reference number available for this part used in Faema brewing groups. This brass square shaft has a overall length of 40mm. The square itself is 5x5mm. the thread used is a male M4 thread. This square shaft goes in the bottom...
€3.37
O ring EPDM 23x3mm
O ring EPDM 23x3mm. This o ring seals off one side of the one way valve. Return to the Faema E61 valve parts overview
€8.06
Faema E61 stickers
On this page you will find the stickers which go on the front panel of the vintage Faema E61 and Faema President lever group. These can get damaged or not present at all. This set contains the Faema water level sticker descriptions, Massimo and Minimo. For the steam valve Vapore, for the water valve Scarico acqua. For the cup warmer valve the Scaldatazze....
€11.07
Faema E61 lever knob
The handle knob on this page can be used on Faema E61 brewing groups. This handle goes on the brewing group control lever. Originally these were made from Bakelite, but nowadays that isn’t made that much anymore. The Faema part reference fort his item is 4741135910 This plastic lever brewing group handle is made from a shiny plastic. In the middle is a...
€13.25
Procon clamp ring pump 180 L/H
On this page you will find a espresso machine pump suitable for a variety of espresso machines. This pump has been made by the company Procon in Ireland. This model is a clamp ring pump, this pump is clamped with a stainless steel clamp to the espresso machine motor. The pump can pump 180 L/H and is fitted with a balanced bypass. To control the pump...
€174.64
E61 group allen key copper washer 10x6,2x1mm
Almost every Faema e61 brewing group made has a Allen bolt on the front of the brewing group, yes there are models which don’t have this hole. This hole also needs to be sealed off. This can be done with PTFE tape. But you can also use a copper gasket for that. The Faema part reference for this item is 4054043102 This flat copper washer has a outer...
€0.60
Faema E61 and president 1 group glass
On this product page you will find a replacement glass for a Faema E61 1 group and a Faema President 1 group lever espresso machine. The outer dimensions of the glass are 365mm by 165mm The distance between the holes is not identical horizontally. Vertically the distance it is about 85mm from centre to centre. For the horizontal distance, centre to centre...
€234.10
Faema E61 valve rod spring
This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...
€1.24
E61 style lever brewing group
On this product page you will find a complete E61 style brewing group. There are a variety of E61 style brewing groups. Examples of this are the Solenoid valve groups, with the solenoid valve at the bottom, or on the sides. This E61 style brewing group can be used on Fiorenzato, Grimac and La Scala espresso machines. The Fiorenzato part reference fort his...
€402.24
Flex pipe 2000mm 3/8 ff conical base
On this page you will find a stainless steel water hose. This hose can be used to connect the water mains to your espresso machine any other suitable appliance. This stainless steel flex hose has a overall length of 2000mm and on each end a 3/8” BSP-G fitting. This connection is conical so there is no need to a gasket. The maximum fluid temperature which...
€20.35
Faema E61 heating element 2 group 2600W 110V
The element shown on this product page can be ideal to make from your 220/230V Faema E61 a 110V model. This heating element has the typical Faema type of brass flange. The element is powered at 110V and supplies 2600W. The immersed length of the element is just 350mm. The heating element gasket used for this element has a outer diameter of 57mm a inner...
€100.60
Compression spring 13x42mm
The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This is the spring located in the upper section of the brewing group, in the trumpet/mushroom. This stainless-steel compression spring has a outer diameter of 13mm. The length of this compression spring is 42mm. This spring has been made in Italy. This...
€2.23
Faema E61 filterbasket double 12gr
Stainless steel double filterbasket for a Faema E61 brewing group. This basket can contain 12grams of coffee. The width of the basket is 70mm and the height of the basket is 22mm.if you are looking for a single filterbasket click there. Return to the Faema E61 group parts overview
€7.10
O ring nbr 8,9x1,9mm
This O ring in nbr with the specifications 8,9x1,9mm. Makes sure that the brass non return valve seals against the body of the non return valve. Return to the Faema E61 valve parts overview
€0.65
Anti vacuum valve V.A.R. 1/4"
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€12.00
Faema E61 plastic top 2 group
On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 2 group are only the measurements of the width and length of the U shape. The length of this plexi is about 455 and the width is 220mm. This plexiglass...
€325.64
Faema E61 stainless steel valve rod
On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...
€14.47
Faema E61 sticker 3 group
Faema E61 sticker 3 group for the glass plate on the back of the machine. Return to the Faema E61 body parts overview
€42.80
Faema E61 upper round rod
Faema E61 brass upper round rod 40x4mm. screws in the valve gasket holder Return to the Faema E61 group parts overview
€3.50
Faema E61 plug for camme holder
This stuffing nut is used to set even pressure on the gaskets of the cam shaft used in the E61 brewing groups. This nut can be used on the classical Faema E61 as well as the modern E61 style brewing groups. Such as Bezzera, La Scala, Grimac, Isomac, Pavoni, Brasilia and Vibiemme. This stuffing nut has been made from nickel and chrome plated brass. The...
€9.81
IMS faema double cup filterbasket 18/22gr
The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. This double filterbasket on this page has the IMS product code B702TCH28.5E or B702TH28.5E This single filterbasket can hold ground coffee from 18 grams up to...
€25.03
Faema E61 valve gasket 13x4x4mm
The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...
€0.81
Faema E61 camme holder
The cam holder shown on this page can be used on the Faema E61 and the Faema E61 Legend. The ones used on the E61 style brewing groups have a different shape. The Faema part reference for this item is 4152135911. This item has been machined from a solid piece of brass. After machining and polishing it has been nickel and chrome plated. This item has been...
€40.46
Portafilter gasket 73x57x9mm red silicone
On this product page you will find a portafilter gasket, but not a standard one. This portafilter gasket has been made from food grade silicone, in the colour red. This product has been made in Italy. The gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 9mm. You can use this on a variety of brands such as the Vibiemme...
€4.14
Faema E61 heating element gasket 57x43x3mm
On this page you will find a heating element gasket we had made out of AFM34 a food safe fibre material, made in Germany. This heating element gasket has a outer diameter of 57mm a inner diameter of 43mm and a thickness of 3mm. This heating element gasket can be used on a variety of heating elements such as the Faema E61, Faema E61 Legend, Faema E61...
€4.89
Faema E61 sleeve
The brass cam guide bushing shown on this page is used on the Faema E61 and E61 style brewing groups. You can use this guide bushing on Faema, Grimac, Vibiemme, La Scala, Bezzera, Wega, Pavoni espresso machines. This brass bushing has a overall length of 28mm. The outer diameters are 10 and 15mm. The inner diameter is 8mm and the head thickness is 5mm....
€3.47
Faema E61 steam valve pin
The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880 This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...
€2.96
Faema E61 flange level side
Faema E61 flange sight glass side. Do you have a small leak in one of your boiler flanges. this can be fixed easily by replacing the flange which is leaking. Next to the level side flange we also offer the heating element side flange. Return to the Faema E61 boiler parts overview
€403.94
Faema E61 filterbasket single 7gr
Stainless steel single filterbasket suitable for a Faema E61 brewing group. The basket can contain 7grams of coffe. The outside diameter is 69,5mm and the height of the basket is 24mm.If you are looking for a double filterbasket click there. Return to the Faema E61 group parts overview
€5.26
IMS Faema double cup filterbasket 12/18gr
A lot of the filterbasket sizes are quite standardized. This IMS filterbasket is good example of this. The basket is made by IMS filtra, but it is a competition basket and not from the standard IMS basket line. The IMS part number for this double filterbasket is B702TH24.5M. The double filterbasket is made from stainless steel 304, food safe. The outer...
€28.03
