Faema E61 spare parts
On this product page you will find a drain sleeve which can be used on the Faema E61 models and on a variety of E61 Style of brewing groups, not all of them will fit. This drain sleeve can be used on the e61 groups of La Scala, Bezzera, Grimac, Faema, Pavoni, Wega and Brasilia. This drain sleeve has been machined from brass and after that it has been...
€72.40
Faema E61 valve rod washer stainless
This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101 This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...
€0.81
Faema E61 microswitch 16A 250V
On this product page you will find a microswitch which can be used on the Faema E61 espresso machines. As well on the Faema E61 Legend espresso machines. The Faema part reference for this switch is Faema 532006600. This switch is rated up to 16A at 250V. This switch has a spring loaded metal pin. This pin get’s pushed inwards when the lever of the group...
€45.31
Boiler top fitting 1/2"
If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...
€20.93
Faema E61 cup warmer knob
Faema E61 plastic cup warmer knob. This knob is used on 2 locations on the Faema E61. The first location is on the regeneration valve. The second location is on the valve to controle the cup warmer ring. this ring is missing on most machines, but you can't miss the valve on a e61!
€4.78
Faema E61 lever knob
The handle knob on this page can be used on Faema E61 brewing groups. This handle goes on the brewing group control lever. Originally these were made from Bakelite, but nowadays that isn’t made that much anymore. The Faema part reference fort his item is 4741135910 This plastic lever brewing group handle is made from a shiny plastic. In the middle is a...
€13.25
Faema E61 steam/water group expanding spring
The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...
€2.48
Faema E61 heating element 2 group 2600W 110V
The element shown on this product page can be ideal to make from your 220/230V Faema E61 a 110V model. This heating element has the typical Faema type of brass flange. The element is powered at 110V and supplies 2600W. The immersed length of the element is just 350mm. The heating element gasket used for this element has a outer diameter of 57mm a inner...
€100.60
Faema E61 non return valve body
Faema E61 brass non return valve body. The side flange is screwed into the main body.If you want to complete the assembly add the following parts to the part:Faema E61 Spring Non Return Valve; O Ring EPDM 8,9x1,9mm; Faema E61 Small Non Return ValveReturn to the Faema E61 valve parts overview
€33.38
Faema E61 steam valve nut gasket 23x18x1mm
Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview
€0.82
Faema E61 PTFE gasket 26x21x2mm
This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...
€1.52
Faema aluminium drain tray
Faema aluminium drain tray. Return to the Faema E61 valve parts overview
€56.33
Faema E61 gigleur spring
Faema E61 stainless steel gigleur spring. if your replacing this part don't forget to replace the rest of the sealing parts of the group. We offer a handy rebuilding kit for that. (the gigleur spring is also in that kit) Return to the Faema E61 group parts overview
€1.76
Faema E61 steam valve pin
The small brass tab spindle can be found on various Faema espresso machines. Primarily in the E61 style of steam and water valve. The Faema part reference for this item is 4811135880 This tab spindle has been made from brass and has a overall length of 20,8mm. You can use this tab spindle on the Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema...
€2.96
E61 style groups shower without welding 60mm
The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...
€3.32
Faema E61 group upper plug
The fitting on this page is the top fitting on almost every E61 brewing group. You can find the male stop on brands such as Vibiemme, La Scala, Bezzera, Grimac, Faema, La Pavoni, Wega and Brasilia espresso machines. This male cap has a diameter of 16mm. It has been made from brass and has been nickel and chrome plated. The thread used is a 3/8” BSP-G...
€5.65
Crushable copper washer 23x17x3mm
The crushable copper gasket on this page can be used with various applications on Brasilia espresso machines. For instance, on sealing off steam and water tubes and as a gasket on various boiler fitting applications. The Brasilia part reference for this item is 01386.0.00.02 This copper gasket has a outer diameter of 23mm a inner diameter of 17mm and a...
€1.72
Faema E61 plastic top 3 group
On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 3 group are only the measurements of the width and length of the U shape.The length of this plexi is about 630mm and the width is 220mm. This cupwarmer...
€353.11
Faema E61 single portafilter
The portafilter on this page looks like a classical Faema E61 portafilter. And that is indeed correct, the style looks quite similar to the antique portafilters used in the Faema Lever brewing groups and Faema E61. But there are some slight differences, the shape is slightly different and the end plug in the portafilter handle is not identical to the...
€110.04
Flat copper gasket 23x17x1.5mm
Flat copper gasket 23x17x1.5mm Return to the Faema E61 valve parts overview
€0.96
Faema E61 complete steam valve
The steam and water valve on this page can be found on various old and new Faema models. The Faema part reference for this item is 903743000 This valve has on the steam/water tube side a female thread of 3/8” BSP-G. On the inlet side the thread is a male 3/8” BSP-G. This steam/water valve does not come with a knob. You can also use the original Bakelite...
€77.47
Faema E61 steam valve knob
On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...
€20.35
Safety valve 3/8'' 1,8 bar
On this page you will find a safety valve which has a male 3/8”BSP-G thread. The pre-set pressure of this valve is 1,8bar. You can adjust it yourself but not recommended. The spring inside the safety valve is made from stainless steel and the sealing material is FKM. The valve has been made in Italy. We do strongly advise to replace the safety valve every...
€16.80
Faema E61 camme holder
The cam holder shown on this page can be used on the Faema E61 and the Faema E61 Legend. The ones used on the E61 style brewing groups have a different shape. The Faema part reference for this item is 4152135911. This item has been machined from a solid piece of brass. After machining and polishing it has been nickel and chrome plated. This item has been...
€40.46
IMS Faema single cup filter basket 7/9 gr
The filterbasket on this page is one of the most commonly found filter basket models. This model is made by IMS Filtri in Italy. The basket is from the competition line and not the standard line. The single filterbasket on this page has the IMS product code B701TH26.5E This single filterbasket can hold ground coffee from 7 grams up to 9grams. The basket...
€25.59
Faema E61 group spring 14x33mm
The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the bottom exhaust valve. When the lever is in the lowest position the valve assembly will push this spring inward and the exhaust valve will open completely. This will make sure that all the exhaust water goes out...
€2.39
Faema E61 stainless steel valve rod
On this page you will find a steam and water valve shaft used in various Faema espresso machines. This valve shaft has the Faema part reference of 4818135879. This valve haft has been made from stainless steel and has a overall length of 76mm. the male thread on the end is a M6. The square end, for the knob, is 7x7mm. You can use this stainless steel...
€14.47
Sirai pressure switch single phase P203/T01 20A
The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...
€99.17
Stainless steel pressure switch bracket
Pressure switch bracket made out of stainless steel 304. The bracket has a length of 90mm and a width of 18mm. This bracket is intended to fix one side to a boiler stud or inbetween a boiler bolt (up to M10).The other side is suitable to fit a pressure switch with a 1/4" BSP-G connector.
€10.48
Faema E61 expansion valve guide
Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview
€5.11
Faema E61 boiler manometer
This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...
€43.61
Portafilter gasket 73x57x9mm
Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
€4.59
Faema E61 sticker 3 group
Faema E61 sticker 3 group for the glass plate on the back of the machine. Return to the Faema E61 body parts overview
€42.80
Anti vacuum valve V.A.R. 1/4"
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€12.00
Faema bottomless portafilter
The bottomless portafilter on this page can be used on a variety of Faema espresso machines. This bottomless portafilter can be used on the antique lever espresso machines as well on the E61 brewing groups. This bottomless portafilter comes with a standard style of handle. The ear orientation is at 90 degrees. The thickness off the ears is 7,2mm. This...
€66.43
