Vibiemme Replica Pistone

Some heating elements have a triangular flange, these are used for some models of Vibiemme, Brasilia and Aurora Brugnetti. This heating element gasket is made from the fibre material AFM34 by Victor Reinz in Germany. This specific element has the outer dimensions of 80x80mm and a thickness of 2mm and is made from a fibre material. If you are not sure if...

This O ring in nbr with the specifications 8,9x1,9mm. Makes sure that the brass non return valve seals against the body of the non return valve. Return to the Faema E61 valve parts overview

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

On this product page you will find a boiler pressure gauge suitable for a variety of Vibiemme espresso machines. The VBM part reference for this manometer is MANM49025GHIR. The pressure gauge can show a boiler pressure from 0 to 2,5bar. The body of the manometer is 49mm, the frame of the pressure gauge is 57mm. This manometer has a capillary with a female...

This flat PTFE gasket is used on various lever espresso machine brewing groups used on the brands Fiorenzato and Vibiemme. The Fiorenzato part reference number is A1200190  and the Vibiemme part reference number is GUARTEFANPIST. This flat gasket is made from PTFE. The outer diameter is 50mm, the inner diameter is 44mm and the thickness is 4mm. The gasket...

This small stainless steel washer can be found on various Faema espresso machine models, mainly the ones which use the E61 style of steam/water valve. The Faema part references for this item are: 4041136008 and 4054043101  This washer is used in between the valve shaft and the tap spindle. This stainless steel washer has a outer diameter of 9mm and a...

Fiorenzato o ring 41,28x3,53mm o ring. This o ring seals the brewing group from the boiler.Return to the Fiorenzato Piazzo San Marco overview

Parker solenoid valve 2 ways base mounting 220/230V 50/60Hz 9WReturn to the Faema E61 Legend water inlet parts overview

Fiorenzato piazza san marco lever group ball bearing. Replacing your old bearing with a new one makes a huge difference in smoothness. Return to the Fiorenzato lever parts overview

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...

The spring on this product page is used for various applications with various brands. This spring is used in water inlet systems, steam and water valves and non return valves. You will find this model of compression spring with brands such as Brasilia, La Spaziale, Faema, Grimac, Vibiemme and La Scala. This stainless steel compression spring has a outer...

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...

Ball valve 1/4M 1/4F

If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...

On this page you will find a brass steam pipe bushing. But what is a pipe bushing. A pipe bushing makes it possible to move the steam and water wand freely without leaking. So how does it work? Well the pipe bushing has on the valve side 2 o rings, these seal against the side of the inside of the valve. But on the top ring of the pipe bushing there is...

O ring 14x2mm

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...

With this steam valve you can clearly see that there are some resemblances between Faema and Vibiemme. Technically it is as good as identical as a e61 valve, the only difference is that the Vibiemme valve has a stainless-steel ball in the valve. Aesthetically the differences are that the chrome plated tap nut is a lot squarer then the original. And one of...

Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview

This oddly looking screw is the right brewing group pin used on the Vibiemme lever espresso machine brewing groups. The Vibiemme part reference number for this item is VITEPERNGRDPI  This screw can only be used on the right side of the brewing group. This group screw is made in Italy. You can use this lever brewing group screw on the lever group used on...

Complete valve spout 54,6mm

The portafilter gasket on this product can be used on various lever espresso machines. On brands such as Fiorenzato and Vibiemme. The Fiorenzato part reference number is A1200194  and the Vibiemme part reference number is GUARSOTPISTON. This portafilter gasket has a outer diameter of 65,5mm a inner diameter of 55,5mm and a thickness of 5,5mm. This gasket...

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...

Vibiemme Replica steam pipe right

The function of a shower screen is to spread the water coming out off the group on a equal way over the coffee. One of the standardized sizes and most common, is the 60mm shower screen. This shower is a pressed model made by IMS IMSDR300. The outer diameter is 60mm, the internal height is 17mm and the diameter of the punctured holes is 2,5mm Note: this is...

The Asco P302/6 is a three-phase pressure switch that is likely the most frequently used pressure switch. Espresso makers like as La Marzocco, Faema, Cimbali, Wega, Astoria, Nuova Simonelli, La Spaziale, San Remo, and others have utilized this pressure switch.The company Sirai used to be the brand Asco; nonetheless, the product is still the same despite...

Faema E61 steam valve nut gasket 23x18x1mm. This PTFE seal creates a water and air tight seal between the steam valve body and the chrome plated brass steam valve flange. Return to the Faema E61 steam/water valve overview

EPDM OR 4,47x1,78

This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...

Faema E61 brass small non return valve. This valve guide is sealed by this o ring and kept on it's place with the non return valve spring. Return to the Faema E61 valve parts overview

On this page you will find the o ring with the cord diameter of 1,9mm and a internal diameter of 7,2mm. This specific o ring is used with a variety of applications in expresso machines. For instance, with Expobar in the water inlet valve. For Faema in the cappuccinatore. With Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg and La Carimali in...

The gasket shown on this product page can be used on various Vibiemme espresso machine boilers. The Vibiemme part reference for this item is GUARFL205T  This boiler gasket has a outer diameter of 165mm a inner diameter of 150mm and a thickness of 3mm. This gasket has been made from PTFE. Made in Italy. You can use this boiler gasket on the Vibiemme Cubo,...

Spring for steam valve

On this page you will find a portafilter gasket specially suited for lever espresso machine brewing groups. This specific portafilter gasket is suitable for brands such as the Astoria, Pavoni, Wega, Victoria Arduino, Fiorenzato and Brasilia lever groups. (seen they are the same model of group) This specific gasket has been made from NBR. This gasket has a...