Brasilia Portofino leva

Brass lever valve with PTFE lining

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

On this product page you will find the injector tube for various lever espresso machine groups. For example used on Astoria, Wega and La Pavoni groups. This item is a OEM/original Astoria/Wega spare part, but can be used with La Pavoni brewing groups. The overall length of this tube is 140mm and the tube has a outer diameter of 12mm. the fittings screws...

On this page you will find the front stop for various lever brewing groups. This front stop make sure tha you don’t damage the lever nor the castings of the brewing group itself. This rubber front stop can be used with brands such as Brasilia with part number 01432.0.00.02 , La Pavoni 477021 and Victoria Arduino 17000018 . For La Pavoni it is only...

On this page you will find a OEM/Original shock absorber for the Astoria and Wega lever brewing groups. This absorber is located inside the lever fork. So when the lever is released by accident this rubber shock absorber will absorb some of the force. This absorber is also used when the lever is in rest position This shock absorber can be used on the...

On this product page you will find the connection between the lever and the lever group itself. In the top of this casted item you will screw the lever itself.  There are 2 holes. 1 of them has a bushing inside so that there is some axial movement possible. In the fixed hole goes the bearing shaft. In the movable hole goes a pin to make a connection with...

Safety valve 1/2"1,8 Certif CE PED IV

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...

The item on this product page is a steam and water valve screw, used on various Brasilia espresso machines. The Brasilia part reference number for this item 00107.4.00.04  This articulating valve screw is used in combination with the spring washers and the conical PTFE gaskets to seal off the valve. This item has been made in Italy. You can use these...

On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...

Brasilia portofino chromed steam pipe

The crushable copper gasket on this page can be used with various applications on Brasilia espresso machines.  For instance, on sealing off steam and water tubes and as a gasket on various boiler fitting applications. The Brasilia part reference for this item is 01386.0.00.02  This copper gasket has a outer diameter of 23mm a inner diameter of 17mm and a...

Brasilia lower level fitting

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

Astroia CMA style complete lever brewing group

On this page you will find a lever fork pin suitable for brands such as the Astoria and Wega. Note, there are more versions available This blank steel pin (so they do rust) is the link between the lever and the piston shaft. This pin has been knurled on one side, this side also grabs into the brass lever group fork. This lever pin is a OEM/Origina (part...

On this page you will find a chrome plated lever group fork for various lever groups. This fork is responsible for transitioning the lever motion to a vertical motion. This chrome plated group fork can’t be used on the older AL lever groups as used by Astoria and Wega. That part is out of production. This specific item is OEM/Original item suitable for...

The valve gasket on this page is one of the most common flat gaskets you can find in a espresso machine. This gasket is made from NBR and has a outer diameter of 13mm a inner diameter of 4mm and a thickness of 4mm. This type originates from Faema espresso machines. where you can find this gasket in the Faema E61, Faema President, Faema Lambro Faema Urania...

The nut on this page is a M3 nut made from brass. You will find this type of nut on variety of steam and water valves of  Astoria and Wega espresso machines. The Astoria part reference for this item is 23050 and the Wega part reference is WY23050. This brass nut has a metric female thread of M3. The nut has made according to specifications of UNI 5587 and...

On this page you will find a plastic handle which goes over a lever brewing group lever. This plastic lever handle can be used with a variety of lever brewing groups such as the ones used with Vibiemme Replica, Astoria Rapallo, La Pavoni Bar, La Pavoni Bart, La Pavoni Pub, Wega Antares, Wega Nova, Victoria Arduino Athena, Brasilia Decurtis AL and so on....

The item on this page is a steam and water valve washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item is 12153.0.00.03. This washer is made from machined brass. the outer diameter is 10,7mm, the inner diameter is 8,2mm and the thickness is 2mm. this washer is made in Italy. You can use this brass washer on...

On this page you will find a lever brewing group main spring. This spring is used to generate the pressure. This type of spring is quite common and will find it in a variety of lever espresso machines. This model has a overall length of 140mm and a outer diameter of 46mm. this spring has been made from standard spring steel and after that it got...

On this page you will find the o ring with the cord diameter of 1,9mm and a internal diameter of 7,2mm. This specific o ring is used with a variety of applications in expresso machines. For instance, with Expobar in the water inlet valve. For Faema in the cappuccinatore. With Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg and La Carimali in...

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...

On this page you will find a rubber back stop used with a variety of and newer lever espresso machine brewing groups. You will find this back stop on Astoria and Wega models pre 2001. Currently you can find them on brewing groups used by Bezzera 5473001 , Pavoni 477020, Victoria Arduino 17000018, Wega WY15101 and Brasilia 01431.0.00.02. For Pavoni groups,...

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

The o ring on this product page is used on various Brasilia steam and water valves on various models. The Brasilia part references for this item are 05825.0.00.02 and 0582500002. This o ring is made from EPDM. The cord diameter is 2,62mm and the internal diameter is 25,07mm. This o ring is made in Italy.  You can use this o ring on the Brasilia Century,...

On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....

This steam pipe bushing is a important element in the sealing and functioning of a steam and water valve. This bushing is pushed down on one side with a spring, this bushing has on the other side a hollow shape so that the ball of the steam and water valve can slide smoothly over the brass. This brass bushing has multiple dimensions. The external diameter...

The sight glass on this page can be used on various Vibiemme espresso machine models. The Vibiemme part reference for this item is MATECVELI140  This sight glass has a outer diameter of 11mm and a overall length of 140mm. this sight glass has silk printing on the glass. There is on the back a red line and on the front the lettering of max and min. This...

Gudgeon pin lever group

Seeger ring 9mm

This sight glass fitting is used on a variety of espresso machine brands such as Vibiemme, La Scala, Brasilia and Gaggia. The Brasilia part reference is 00089.0.10.04 , the Gaggia reference is LV0505 and the Vibiemme (VBM) part references are RACCP227 and RACCP427. This sight glass fitting has a male 3/8” BSP-G thread. The central hole is for the sight...

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...

One of the most universal items. The male brass plug. The plus on this page can be found in the catalogue of a variety of espresso machine manufacturers like Astoria, Faema, La Spaziale and Wega. This specific plug has a male ¼”BSP-G thread. The height of this plug is 13 mm and the wrench size for this plug is 17mm.