0
My cart
Astoria CMA lever operated espresso machines
Asco/Sirai pressure switch P303/T01 3 phase 20A
On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€88.64
Tap joint spring 12x15mm
The steam pipe spring on this page is suitable for a variety of espresso machine brands, it’s also a universal item. This spring make sure that you can leave your steam tube in a fixed position. If there is no spring, it will fall back to the lowest point. This spring has a external diameter of 12mm and a overall length of 15mm and is made from stainless...
€2.41
Astoria Wega boiler gasket 190x138x3mm
The boiler gasket on this page is used to seal off the boiler flange with the rest of the boiler. This model of gasket is used with Astoria and Wega espresso machines. The Astoria part number is 12003 and the Wega part number is WY12003. This boiler gasket is made from the material PTFE. The outer diameter is 191mm, the inner diameter is 139mm and the...
€40.95
Astoria front stop
On this page you will find the front stop for various lever brewing groups. This front stop make sure tha you don’t damage the lever nor the castings of the brewing group itself. This rubber front stop can be used with brands such as Brasilia with part number 01432.0.00.02 , La Pavoni 477021 and Victoria Arduino 17000018 . For La Pavoni it is only...
€21.76
Astoria portafilter gasket 67x56x5.5mm original
Astoria portafilter gasket 67x56x5.5mm original
€5.04
Astoria fork rod post 2001
On this product page you will find the connection between the lever and the lever group itself. In the top of this casted item you will screw the lever itself. There are 2 holes. 1 of them has a bushing inside so that there is some axial movement possible. In the fixed hole goes the bearing shaft. In the movable hole goes a pin to make a connection with...
€102.41
Safety valve 3/8" 2.0 bar CE PED IV certified
On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€10.47
Wega heating element 2 gr 2600W 230V
Wega heating element 2 gr 2600W 230VType flangedwatt 2600wvolt 230/400V
€74.25
Lever group shower 57mm
A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...
€12.79
Lever group handle
On this page you will find a plastic handle which goes over a lever brewing group lever. This plastic lever handle can be used with a variety of lever brewing groups such as the ones used with Vibiemme Replica, Astoria Rapallo, La Pavoni Bar, La Pavoni Bart, La Pavoni Pub, Wega Antares, Wega Nova, Victoria Arduino Athena, Brasilia Decurtis AL and so on....
€13.44
Fiorenzato o ring upper brewing group
A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...
€4.08
Astoria heating element 4500W 230/380V
Astoria heating element 4500W 230/380V L 310mmType flangedwatt 4500volt 230/400length (mm) 310
€79.32
PTFE gasket 20x17x2mm
PTFE gasket 20x17x2mm. Suitable for:CodeProducer12010 Astoria CMA000466 Aurora-brugnetti000501 Aurora-brugnetti400-215-000 Cimbali400215000 Cimbali401-183-000 Cimbali401-183-010 CimbaliC469900420 Ecm401183000 Faema401183010 Faema4701024558 Faema01539006 Futurmat-Ariete05132808 Futurmat-ArieteISGUATF22172 Isomac...
€1.08
Lever group spring 131mm
On this product page you will find the main spring for a lever brewing group. This spring is mainly used on older models of Bezzera espresso machines. This spring has a overall length of 131mm. the outer diameter of this compression spring is 46mm. The material used for this spring is just regular spring steel which has been galvanized. You can use this...
€47.99
Anti vacuum valve V.A.R. 1/4"
On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...
€10.91
Lever new brewing group cover
This black plastic cover is used with a variety of lever espresso machine groups. This keeps the mechanism clean and you won’t get your fingers stuck in the bearing mechanism. This plastic cover has been manufactured in Italy. This cover can be used for various lever brewing groups such as with the Astoria, the old La Pavoni groups, Wega Antares, Wega...
€23.36
Lever group joint pre-2001
On this page you will find the lever fork for various lever brewing groups. One of the holes is for the bearing pin hole and the other one is for transferring the puling motion to the vertical spring motion. This specific lever fork is specifically for lever groups which are pre-2001 lever brewing groups. This item is out of production and not available...
€66.78
Level indicator red ball
This red ball is a level indicator ball. This ball floats inside the water level tube. Seen it’s not always easy to see the water level makes a floating red ball it a lot easier. There are more colours available with different diameter of balls. This red ball has a diameter of 5,8mm and is made in Italy. This type of level indicator can be found in a...
€2.18
Astoria/Wega water level nut 1/2" 12mm
This page shows the water level nut for a Astoria and Wega sight glass. This nut makes sure that the sight glass stays in place and seals properly. If the nut is screwed down the sight glass seal will slightly compress and seal off the sight glass. The part number for this item is for Astoria is 25383 and for Wega WY25383 This sight glass nut has a...
€8.38
Astoria bottomless portafilter
The bottomless portafilter on this product page can be used on a variety of Astoria espresso machines. The Astoria part reference number for this item is 27311004. The portafilter has a ear orientation of 45 degree, the ear thickness is 6mm. The portafilter does come with a double filter basket and stainless steel spring. This portafilter is made in...
€60.39
Beating rubber lever group
On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...
€11.74
Lever group spring 140mm
On this page you will find a lever brewing group main spring. This spring is used to generate the pressure. This type of spring is quite common and will find it in a variety of lever espresso machines. This model has a overall length of 140mm and a outer diameter of 46mm. this spring has been made from standard spring steel and after that it got...
€34.56
Astoria lever fork pre 2001
Astoria lever group fork pre 2001 Return to the Astoria lever parts overview
€134.19
Paper shim 66x58x0,8mm
On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...
€1.10
Male plug 1/4"
One of the most universal items. The male brass plug. The plus on this page can be found in the catalogue of a variety of espresso machine manufacturers like Astoria, Faema, La Spaziale and Wega. This specific plug has a male ¼”BSP-G thread. The height of this plug is 13 mm and the wrench size for this plug is 17mm.
€2.72
Astoria lever group fork
On this page you will find a chrome plated lever group fork for various lever groups. This fork is responsible for transitioning the lever motion to a vertical motion. This chrome plated group fork can’t be used on the older AL lever groups as used by Astoria and Wega. That part is out of production. This specific item is OEM/Original item suitable for...
€74.25
Astoria Wega steam pipe chrome plated Original part
Astoria Wega steam pipe chrome plated Original part
€52.35
A Heritage of Excellence
With roots dating back to 1969, Astoria CMA has established itself as a beacon of excellence in the espresso industry. The company's commitment to quality and innovation shines through in every aspect of their lever-operated machines.
Timeless Design and Precision Engineering
Astoria CMA lever-operated espresso machines are renowned for their timeless design and precision engineering. Crafted with meticulous attention to detail, these machines marry classic aesthetics with modern functionality, resulting in an espresso-making experience that is both elegant and efficient.
Unmatched Control and Flavour
At the heart of every Astoria CMA lever-operated machine lies a sophisticated lever mechanism that provides baristas with unparalleled control over the brewing process. This level of precision allows for the extraction of rich, flavorful espresso shots that are sure to delight even the most discerning coffee aficionados.
Versatility to Suit Every Setting
Whether you're a home barista looking to elevate your coffee game or a professional seeking a reliable workhorse for your café, Astoria CMA lever-operated machines offer versatility to suit every setting. Available in a range of sizes and configurations, these machines are designed to meet the unique needs of any coffee lover or business owner.
Superior Quality Spare Parts and Support
Our store is proud to offer a comprehensive selection of high-quality spare parts for Astoria CMA lever-operated espresso machines. From gaskets and seals to levers and portafilters, we have everything you need to keep your machine running smoothly and producing delicious espresso for years to come. Plus, our team of experts is always on hand to provide assistance and support, ensuring that you get the most out of your Astoria CMA machine.
Conclusion: Elevate Your Espresso Experience with Astoria CMA
In conclusion, Astoria CMA lever-operated espresso machines embody the perfect blend of heritage, craftsmanship, and innovation. Whether you're a seasoned barista or a coffee enthusiast looking to take your brewing skills to the next level, these machines offer an unmatched espresso experience that is sure to impress. Explore our range of Astoria CMA lever-operated machines today and discover the perfect addition to your coffee setup!