Filter by
Price
Type part
more... less
Filter

Victoria Arduino Athena 2006

Our selection of Victoria Arduino Athena parts

Victoria Arduino Parts Athena

Safety valve 3/8" 2.0 bar CE PED IV certified

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...
€12.87

Lever group handle

On this page you will find a plastic handle which goes over a lever brewing group lever. This plastic lever handle can be used with a variety of lever brewing groups such as the ones used with Vibiemme Replica, Astoria Rapallo, La Pavoni Bar, La Pavoni Bart, La Pavoni Pub, Wega Antares, Wega Nova, Victoria Arduino Athena, Brasilia Decurtis AL and so on....
€11.69

Lever group shower 57mm

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...
€11.12

Valve rod washer 20x6.3x1.5mm

Valve rod washer 20x6.3x1.5. Suitable for:CodeProducer93.00058 Carimali25012521 Expobar30370100 Expobar4054043423 FaemaL165/9 MarzoccoL165/9B Marzocco00000096 Nuova Simonelli10402040 Sanremo
€0.53

Silicone piston gasket 52x40x7mm

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...
€3.46

Lever group joint pre-2001

On this page you will find the lever fork for various lever brewing groups. One of the holes is for the bearing pin hole and the other one is for transferring the puling motion to the vertical spring motion. This specific lever fork is specifically for lever groups which are pre-2001 lever brewing groups. This item is out of production and not available...
€58.07

Lever new brewing group cover

This black plastic cover is used with a variety of lever espresso machine groups. This keeps the mechanism clean and you won’t get your fingers stuck in the bearing mechanism. This plastic cover has been manufactured in Italy. This cover can be used for various lever brewing groups such as with the Astoria, the old La Pavoni groups, Wega Antares, Wega...
€20.32

Asco/Sirai pressure switch P303/T01 3 phase 20A

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...
€94.94

Fiorenzato o ring bottom

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The lower o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 56,75mm. This specific o...
€2.99

Sirai pressure switch single phase P203/T01 20A

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...
€92.40

Tap joint spring guide

This steam pipe bushing is a important element in the sealing and functioning of a steam and water valve. This bushing is pushed down on one side with a spring, this bushing has on the other side a hollow shape so that the ball of the steam and water valve can slide smoothly over the brass. This brass bushing has multiple dimensions. The external diameter...
€0.96

Split pin 2x10mm

Split pin 2x10. Suitable for:CodeProducer94.00092 Carimali30370110 Expobar4061024965 Faema05160007 Futurmat-ArieteL165/8 Marzocco9007709 Reneka10806370B Sanremo
€0.77

Paper shim 66x58x0,8mm

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...
€0.96

Faema P4/No stop steam valve rod

Faema steam valve rod P4/No stop. Suitable for:CodeProducer30370050 Expobar3811-117123 Faema3811117123 Faema11156502 Futurmat-Ariete11156530 Futurmat-ArieteL169 Marzocco311333 Pavoni10402061 SanremoRACCASTARUBK Vibiemme
€7.74

Tap joint spring 12x15mm

The steam pipe spring on this page is suitable for a variety of espresso machine brands, it’s also a universal item. This spring make sure that you can leave your steam tube in a fixed position. If there is no spring, it will fall back to the lowest point. This spring has a external diameter of 12mm and a overall length of 15mm and is made from stainless...
€1.92

Faema P4 spring for valve

Faema spring for P4 valve. Suitable for:CodeProducer30370040 Expobar4731-103918 Faema4731103918 Faema08389900 Futurmat-Ariete10391803 Futurmat-ArieteL165/4 Marzocco311427 Pavoni9007705 Reneka10402014 SanremoMOLLAASTAREVO VibiemmeMOLLAASTARUBK Vibiemme
€1.10