Victoria Arduino Athena 2006

Crushable copper washer 22x16x3mm

Faema steam/water valve knob. Suitable for:CodeProducer000222 Brugnetti-auroraL165/V Marzocco40500002 Nuova Simonelli

O ring  5.7x1.9mm nbr

Seeger ring 9mm

Victoria Arduino portafilter single spoutReturn to the portafilter overview

Gaggia steam water valve spring

Non return valve 1/4M

Brass nipple 1/4"M x 3/8"M BSP-G Return to our fitting overview

Gaggia O ring 47,63x3,53mm

On this page you will find a portafilter gasket specially suited for lever espresso machine brewing groups. This specific portafilter gasket is suitable for brands such as the Astoria, Pavoni, Wega, Victoria Arduino, Fiorenzato and Brasilia lever groups. (seen they are the same model of group) This specific gasket has been made from NBR. This gasket has a...

Victoria Arduino bottomless portafilterReturn to the portafilter overview

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...

Nuova Simonelli heating element 3/4 group 5000W 230/380V L 570mm

Faema P4 water knob. Suitable for:CodeProducer30370120 ExpobarL165/MA Marzocco

Brass lever valve with PTFE lining

On this page you will find a plastic handle which goes over a lever brewing group lever. This plastic lever handle can be used with a variety of lever brewing groups such as the ones used with Vibiemme Replica, Astoria Rapallo, La Pavoni Bar, La Pavoni Bart, La Pavoni Pub, Wega Antares, Wega Nova, Victoria Arduino Athena, Brasilia Decurtis AL and so on....

Faema Steam knob insert. Suitable for:CodeProducer30370130 Expobar4831131214 FaemaL165/MV Marzocco

Ode 3 way solenoid valve 1/4" 1/4" 220/230V  DN1,5mm. 

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

Silicone gasket 12.3x5.6mm. Suitable for:CodeProducer95.05031 Carimali30370060 Expobar11181302 Futurmat-ArieteL165/5 Marzocco362074 Pavoni9007703 Reneka10505558 SanremoGUARSILRUBEVO VibiemmeGUARTECIECARK Vibiemme

La Spaziale o ring 11,1X1,78mm

On this page you will find a lever brewing group main spring. This spring is used to generate the pressure. This type of spring is quite common and will find it in a variety of lever espresso machines. This model has a overall length of 140mm and a outer diameter of 46mm. this spring has been made from standard spring steel and after that it got...

La Cimbali M32 sight glass 12x110mm

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...

Steam and water valve complete. suitable forAurora BrugnettiBFC roayl;Brasilia;Faema;La ScalaSV SABVictoria Arduino

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...

Valve rod washer 20x6.3x1.5. Suitable for:CodeProducer93.00058 Carimali25012521 Expobar30370100 Expobar4054043423 FaemaL165/9 MarzoccoL165/9B Marzocco00000096 Nuova Simonelli10402040 Sanremo

Quite often you see that bearings are used in sort of a way. The same in this situation with a lever brewing group. The bearing in this case is slid over the bearing pin axle. When you lower the lever the bearing will make the action more easily. This bearing has a inner diameter of 10mm so it can be slid over the bearing axle. It is a sealed bearing so...

The steam pipe spring on this page is suitable for a variety of espresso machine brands, it’s also a universal item. This spring make sure that you can leave your steam tube in a fixed position. If there is no spring, it will fall back to the lowest point. This spring has a external diameter of 12mm and a overall length of 15mm and is made from stainless...

This steam pipe bushing is a important element in the sealing and functioning of a steam and water valve. This bushing is pushed down on one side with a spring, this bushing has on the other side a hollow shape so that the ball of the steam and water valve can slide smoothly over the brass. This brass bushing has multiple dimensions. The external diameter...

This black plastic cover is used with a variety of lever espresso machine groups. This keeps the mechanism clean and you won’t get your fingers stuck in the bearing mechanism. This plastic cover has been manufactured in Italy. This cover can be used for various lever brewing groups such as with the Astoria, the old La Pavoni groups, Wega Antares, Wega...

Faema spring for P4 valve. Suitable for:CodeProducer30370040 Expobar4731-103918 Faema4731103918 Faema08389900 Futurmat-Ariete10391803 Futurmat-ArieteL165/4 Marzocco311427 Pavoni9007705 Reneka10402014 SanremoMOLLAASTAREVO VibiemmeMOLLAASTARUBK Vibiemme

Level probe 1/4 125mm

Anti vacuum valve 1/4".

Ball Valve 3/8 MF

On this page you will find the lever fork for various lever brewing groups. One of the holes is for the bearing pin hole and the other one is for transferring the puling motion to the vertical spring motion. This specific lever fork is specifically for lever groups which are pre-2001 lever brewing groups. This item is out of production and not available...