Victoria Arduino Athena 2006

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

Ode 3 way solenoid valve 1/4" 1/4" 220/230V  DN1,5mm. 

Quite often you see that bearings are used in sort of a way. The same in this situation with a lever brewing group. The bearing in this case is slid over the bearing pin axle. When you lower the lever the bearing will make the action more easily. This bearing has a inner diameter of 10mm so it can be slid over the bearing axle. It is a sealed bearing so...

La Spaziale o ring 11,1X1,78mm

Seeger ring 9mm

Faema P4 water knob. Suitable for:CodeProducer30370120 ExpobarL165/MA Marzocco

Steamtube anti scorch clip 10mm

Anti vacuum valve 1/4".

Victoria Arduino bottomless portafilterReturn to the portafilter overview

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...

Brass L Fitting 3/8" BSP-G MM Return to our fitting overview

Valve rod washer 20x6.3x1.5. Suitable for:CodeProducer93.00058 Carimali25012521 Expobar30370100 Expobar4054043423 FaemaL165/9 MarzoccoL165/9B Marzocco00000096 Nuova Simonelli10402040 Sanremo

Steam and water valve complete. suitable forAurora BrugnettiBFC roayl;Brasilia;Faema;La ScalaSV SABVictoria Arduino

Conical portafilter gasket 66x56x6mm

Crushable copper washer 22x16x3mm

Brass lever valve with PTFE lining

On this page you will find the lever fork for various lever brewing groups. One of the holes is for the bearing pin hole and the other one is for transferring the puling motion to the vertical spring motion. This specific lever fork is specifically for lever groups which are pre-2001 lever brewing groups. This item is out of production and not available...

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...

Nuova Simonelli heating element 2 gr 3000W 230/380V Type flangedwatt 3000volt 230/380vlength (mm) 340

O ring  5.7x1.9mm nbr

Rancilio steam/water valve joint o ring 12,1x2,7mm

Gaggia steam water valve spring

Brass half nut 1/2" BSP-G 6mm Return to our fitting overview

Gudgeon pin lever group

Non return valve 1/4M

This black plastic cover is used with a variety of lever espresso machine groups. This keeps the mechanism clean and you won’t get your fingers stuck in the bearing mechanism. This plastic cover has been manufactured in Italy. This cover can be used for various lever brewing groups such as with the Astoria, the old La Pavoni groups, Wega Antares, Wega...

PTFE gasket 20x17x2mm. Suitable for:CodeProducer12010 Astoria CMA000466 Aurora-brugnetti000501 Aurora-brugnetti400-215-000 Cimbali400215000 Cimbali401-183-000 Cimbali401-183-010 CimbaliC469900420 Ecm401183000 Faema401183010 Faema4701024558 Faema01539006 Futurmat-Ariete05132808 Futurmat-ArieteISGUATF22172 Isomac...

On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...

Victoria Arduino portafilter single spoutReturn to the portafilter overview

La Cimbali M32 sight glass 12x110mm

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

Faema steam valve rod P4/No stop. Suitable for:CodeProducer30370050 Expobar3811-117123 Faema3811117123 Faema11156502 Futurmat-Ariete11156530 Futurmat-ArieteL169 Marzocco311333 Pavoni10402061 SanremoRACCASTARUBK Vibiemme

Faema Steam knob insert. Suitable for:CodeProducer30370130 Expobar4831131214 FaemaL165/MV Marzocco

Faema No stop valve fitting. pitch 1mm. Suitable for:CodeProducer30370010 Expobar4851117523 FaemaL168/0 Marzocco312226 PavoniRACC3FRUBKO VibiemmeRACCGUIASTEVO Vibiemme

Nuova Simonelli heating element gasket 67x55x3mm

On this product page you will find the bearing pin used in a variety of lever espresso machines, such as Astoria, Wega, Pavoni and Brasilia. This pin has a knurled middle piece. On that location the chrome plated lever fork will be installed to. And next to that you will get 2 bearings. These are secured with 2 shaft clips. This item is OEM/Original...