Vivun keittoryhmän osat

La Pavoni lever shaftReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

On this page you will find a OEM/Original lever group fork made by the Bezzera brand from Italy. This fork is used in various lever brewing group models with the Bezzera brand. The part reference of this item is 5284501.01NC This lever fork is the connection between the piston and lever itself. This part has been made from casted and machined brass. After...

Fiorenzato piazza san marco lever group ball bearing. Replacing your old bearing with a new one makes a huge difference in smoothness. Return to the Fiorenzato lever parts overview

The item on this product page is a OEM/original La Pavoni spare part. This chrome nut is used on top of various domestic lever brewing groups made by La Pavoni. This nut can be used on pre-millennium as well as millennium espresso machines. The La Pavoni part reference for this item is 3135014. This nut has on the inside a M10 thread. The outer key size...

This item is the top section of the lever mechanism used on the Conti lever brewing groups. The Conti part reference on this item is 201800  This chrome plated lever group fork is used to transfer the pulling motion of the lever to a vertical movement. That of the piston. This item has been made from chrome plated brass. This item is available on...

Gaggia steel ballReturn to the Gaggia Italia group overview

This cam guide is vital in the lever mechanism used on the old Gaggia lever brewing groups. This cam guide is installed inside the side of the brewing group. The  lever cams do slide over this shaft. This item is not in production anymore.

On this page you will find a plastic handle which goes over a lever brewing group lever. This plastic lever handle can be used with a variety of lever brewing groups such as the ones used with Vibiemme Replica, Astoria Rapallo, La Pavoni Bar, La Pavoni Bart, La Pavoni Pub, Wega Antares, Wega Nova, Victoria Arduino Athena, Brasilia Decurtis AL and so on....

The item on this page is a brass piston for La Pavoni and Gaggia lever espresso machine groups. This piston can be used on pre-millennium and millennium brewing groups. In the period between approx. 1996 and 2006 the pistons were made from Teflon. This idea was discontinued after 2006 and they got back to the brass pistons again. The Gaggia part reference...

La Cimbali brass lever group piston. The piston keeps both springs on it's place and guides them. on the top of the piston the piston shaft is screwed into the top. The piston doesn't come with the seals. they can be found thereReturn to the La Cimbali M15 overview page

On this page you will find the aluminium lever group cover used in a variety of Faema Lever brewing groups. What is the purpose of this item? Mainly esthetical. But it also prevents dust getting in the brewing group mechanism and the chance also reduces that someone get’s its finger stuck in the bearing mechanism. On what kind of lever brewing groups can...

La Pavoni inox ballReturn to the La Pavoni lever group parts overview

It is quite common that the pinion gear on the Gaggia lever brewing group needs to be replaced. This can be from various reasons, like breaking or damaging teeth. This pinion gear is used to lower and raise the piston shaft in the brewing group. The shaft itself is installed in between 2 sealed bearings. Note: these shafts are made from steel so they can...

Gudgeon pin lever group

This item is a Conti lever brewing group spare part. It is called a traction support. This item is made from casted brass and has 2 bushings installed into it. This item is available on request.

La Pavoni lever group screwReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

La Pavoni connecting rod. Return to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

This item is the nut installed on the top of the piston shaft on various Gaggia lever espresso machines. With this you can fixate the bottom nut. This item is unfortunately out of production and won’t be made anymore.

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

On this product page you will find the connection between the lever and the lever group itself. In the top of this casted item you will screw the lever itself.  There are 2 holes. 1 of them has a bushing inside so that there is some axial movement possible. In the fixed hole goes the bearing shaft. In the movable hole goes a pin to make a connection with...

Basically, every lever espresso machine brewing group has a piston shaft and a lever fork, might look different but the idea is the same. These 2 items need to be connected to each other, so that the force can be transferred. That’s why you have a piston shaft pin. This pin is knurled on 1 side. When you install the pin, this knurling will tighten itself...

On this page you will find a regulator rod for a Faema lever brewing group. With this regulator rod you can set the amount of water flowing into the brewing group chamber. This item has been made from brass and uses a o ring to seal off the shaft of the regulator rod. This regulator rod can be used on a variety of lever brewing groups of Faema, but always...

La Cimbali group locking nut. these nuts screw the inner flange of the brewing group to the brewing group itself. Which makes a air and water tight. Return to the La Cimbali lever parts overview

Bezzera spring rod

La San Marco lever handle. The lever doesn't come with the handle and top screw. these can be ordered seperatelyReturn to the  San Marco group parts overview

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...

The item on this page is a Gaggia lever group piston shaft. This item is made up out of a gear rack and the bottom coupler. This coupler can be easily disconnected from the piston shaft itself. This coupler can be attached to the stainless steel piston. This item is unfortunately out of production and not available anymore.