Vivun keittoryhmän osat

La Cimbali brass lever group piston. The piston keeps both springs on it's place and guides them. on the top of the piston the piston shaft is screwed into the top. The piston doesn't come with the seals. they can be found thereReturn to the La Cimbali M15 overview page

Faema lever group cap Return to the Faema Zodiac lever parts overview

La Cimbali group locking nut. these nuts screw the inner flange of the brewing group to the brewing group itself. Which makes a air and water tight. Return to the La Cimbali lever parts overview

Bezzera group elbow fitting Return to the Bezzera lever parts overview

Rancilio lever cover. Return to the  Rancilio group parts overview

On this product page you will find the bearing pin used in a variety of lever espresso machines, such as Astoria, Wega, Pavoni and Brasilia. This pin has a knurled middle piece. On that location the chrome plated lever fork will be installed to. And next to that you will get 2 bearings. These are secured with 2 shaft clips. This item is OEM/Original...

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

La Pavoni lever shaftReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

Gaggia short cammeReturn to the Gaggia Italia lever group parts overview

La Pavoni boltReturn to the La Pavoni Bar modern parts overview

Faema Mercurio ja Faema Urania pohjaventtiili. Onko tiivis rengas rikki sinun ja ei enää sopiva sinetti. Vaihda se uudella.

Gaggia steel ballReturn to the Gaggia Italia group overview

It is quite common that the pinion gear on the Gaggia lever brewing group needs to be replaced. This can be from various reasons, like breaking or damaging teeth. This pinion gear is used to lower and raise the piston shaft in the brewing group. The shaft itself is installed in between 2 sealed bearings. Note: these shafts are made from steel so they can...

Bezzera spring rod

Gaggia big cammeReturn to the Gaggia Italia lever group parts overview

The item on this product page is a lip seal or shaft gasket. This seal closes off the piston shaft, but you are still able to move the lever. This shaft gasket van be used on early pre-millennium brewing groups as well on millennium brewing groups. The item can be found on domestic La Pavoni lever espresso machines, as well on Gaggia espresso machines....

The item on this page you will find a OEM/Original La Pavoni spare part. This nut can be used on La Pavoni pre-millennium and millennium lever brewing groups. This nut is used as a counter nut for the shaft nut. The La Pavoni part reference for this item is 3135264. This nut has a internal M10 thread. The key size for this nut is 14mm. the height of this...

This oddly looking screw is the right brewing group pin used on the Vibiemme lever espresso machine brewing groups. The Vibiemme part reference number for this item is VITEPERNGRDPI  This screw can only be used on the right side of the brewing group. This group screw is made in Italy. You can use this lever brewing group screw on the lever group used on...

The item on this product page is a OEM/original La Pavoni spare part. This chrome nut is used on top of various domestic lever brewing groups made by La Pavoni. This nut can be used on pre-millennium as well as millennium espresso machines. The La Pavoni part reference for this item is 3135014. This nut has on the inside a M10 thread. The outer key size...

La Pavoni lever group screwReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

Faema retention valve body Return to the Faema Zodiac lever parts overview

Basically, every lever espresso machine brewing group has a piston shaft and a lever fork, might look different but the idea is the same. These 2 items need to be connected to each other, so that the force can be transferred. That’s why you have a piston shaft pin. This pin is knurled on 1 side. When you install the pin, this knurling will tighten itself...

The item on this page is a brass piston for La Pavoni and Gaggia lever espresso machine groups. This piston can be used on pre-millennium and millennium brewing groups. In the period between approx. 1996 and 2006 the pistons were made from Teflon. This idea was discontinued after 2006 and they got back to the brass pistons again. The Gaggia part reference...

The item on this page is a item used on the lever mechanism of various Conti lever brewing groups. The Conti part reference on this item is 202000. This casted brass item is the mid piece of the Conti lever brewing group. This casted piece has 3 bushings installed, this prevents excessive wear on the brass mechanism. You can use this Conti spare part on...

This black plastic cover is used with a variety of lever espresso machine groups. This keeps the mechanism clean and you won’t get your fingers stuck in the bearing mechanism. This plastic cover has been manufactured in Italy. This cover can be used for various lever brewing groups such as with the Astoria, the old La Pavoni groups, Wega Antares, Wega...

The item on this page is a Gaggia lever brewing group spring guide, this item can be found on the Gaggia C70/C80 brewing groups. The spring guide, keeps the main compression spring centred, has been made from pressed copper. Limited stock available

This cam guide is vital in the lever mechanism used on the old Gaggia lever brewing groups. This cam guide is installed inside the side of the brewing group. The  lever cams do slide over this shaft. This item is not in production anymore.

La Pavoni lever pinReturn to the La Pavoni P-90/P-91/P-1/P-3 lever group parts overview

Gudgeon pin lever group

This item is the nut installed on the top of the piston shaft on various Gaggia lever espresso machines. With this you can fixate the bottom nut. This item is unfortunately out of production and won’t be made anymore.

Rancilio stainless steel washerReturn to the  Rancilio group parts overview

Faema top valve cap

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...

Fiorenzato piazza san marco lever group ball bearing. Replacing your old bearing with a new one makes a huge difference in smoothness. Return to the Fiorenzato lever parts overview

On this product page you will find a lever piston used from 03 2006 in various Bezzera lever groups such as the Bezzera Strega, Bezzera Ellisse AL and the Bezzera Ebbis AL. This piston has been made from brass and has a outer diameter of 50mm. The Bezzera part reference for this piston is 5224201