Suodata
Price
Kirjoita osa
more... less
Brändi
more... less
Filter

Tuotemerkit

Espressoperinteen alkuperän paljastaminen

Vipukäyttöisten espressokoneiden matka alkoi 1900-luvun alussa Italiassa, jossa kahvikulttuuri kukoisti vilkkaissa kahviloissa ja espressobaareissa. Keksijät pyrkivät yksinkertaistamaan espresson valmistusta, ja he toivat markkinoille vipukoneet, jotka mullistivat tavan valmistaa ja nauttia kahvia. Nämä varhaiset innovaatiot loivat perustan nykyaikaiselle espressotekniikalle ja muokkasivat kahvin historiaa vuosikymmeniksi eteenpäin.

Tuotteita yhteensä 896 kpl.

Näytetään 1-36 yht. 896 tuotteesta

Conti-vipuryhmähaarukka

This item is the top section of the lever mechanism used on the Conti lever brewing groups. The Conti part reference on this item is 201800  This chrome plated lever group fork is used to transfer the pulling motion of the lever to a vertical movement. That of the piston. This item has been made from chrome plated brass. This item is available on...
43,59 €

Water level nut

This sight glass fitting is used on a variety of espresso machine brands such as Vibiemme, La Scala, Brasilia and Gaggia. The Brasilia part reference is 00089.0.10.04 , the Gaggia reference is LV0505 and the Vibiemme (VBM) part references are RACCP227 and RACCP427. This sight glass fitting has a male 3/8” BSP-G thread. The central hole is for the sight...
6,42 €

Faema Aluminium ryhmäpää

A common problem with the aluminium Faema Zodiac lever brewing group casting is that over time the back of the aluminium group can snap off. Repairing this is normally quite a difficult challenge. This casting has been used on a variety of espresso machine models made by Faema. Like the Faema President and the Faema Lambro. Seen the parts for the Zodiac...
322,51 €

La Pavoni Europiccola kromipähkinä

The item on this product page is a OEM/original La Pavoni spare part. This chrome nut is used on top of various domestic lever brewing groups made by La Pavoni. This nut can be used on pre-millennium as well as millennium espresso machines. The La Pavoni part reference for this item is 3135014. This nut has on the inside a M10 thread. The outer key size...
8,24 €

Lever group spring 168x46mm stainless steel

On this product page you will find a Stainless steel lever group spring. We had this spring modelled after a original one. The to reach a similar spring rate the coil diameter is slightly different then with a standard steel spring. The spring has a overall length of approximately 168mm and a outer diameter of approximately 46mm. Why approximately? Seen...
35,83 €

La Pavoni Europiccola M11x1 adapter and manometer

Originally you would only find a boiler pressure manometer on the La Pavoni Professional espresso machines. This boiler pressure manometer is mounted on the top sight glass fitting. If you want to convert your La Pavoni Europiccola and fit it with a Pressure gauge, this is the kit you need The sight glass fittings used to have a internal diameter of...
47,99 €

Faema männän akseli

Also with the Faema Zodiac groups it is possible that your piston shaft needs replacing, if for instance your lever pin has worn out the attachment hole and there is play on it. Keep in mind that not all piston shafts are interchangeable due to the length of these shafts. This specific shaft has a length of 183mm, this does also include the threads. The...
103,85 €

Conti portafilter yksi suutin

The single portafilter on this product page can be used on the Conti lever brewing groups. The Conti part reference for this item is 409998 This is a single coffee filter holder. The spout is completely open, which makes it easier to clean. The ear orientation of this portafilter is 90degree. The thickness of the ears is 7,4mm. This filter holder comes...
67,03 €

Portafilter tiiviste 73x57x9mm

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...
4,17 €

La Pavoni Europiccola tuloputki

On this page you will find a brass tube which is used in a variety of lever espresso machine models. This brass tube is used in the pre-millennium and Millennium brewing groups of La Pavoni and the millennium groups of Gaggia. The La Pavoni part reference is 326002 and the Gaggia part reference number is S326002. This brass suction pipe has a outer...
20,64 €

Triangular heating element gasket 80x80x2mm

Some heating elements have a triangular flange, these are used for some models of Vibiemme, Brasilia and Aurora Brugnetti. This heating element gasket is made from the fibre material AFM34 by Victor Reinz in Germany. This specific element has the outer dimensions of 80x80mm and a thickness of 2mm and is made from a fibre material. If you are not sure if...
2,70 €

La Pavoni Europiccola and Professional base foot 30mm

The item on this product page is a OEM/Original La Pavoni spare part. This item is the rubber foot which goes underneath various La Pavoni and Gaggia domestic lever espresso machines. The part reference for this item is for Gaggia S371101 and for La Pavoni 371101. This rubber foot has a outer diameter of 30mm and can be installed in the base plates with...
4,62 €

Jatkuva keskivipu

The item on this page is a item used on the lever mechanism of various Conti lever brewing groups. The Conti part reference on this item is 202000. This casted brass item is the mid piece of the Conti lever brewing group. This casted piece has 3 bushings installed, this prevents excessive wear on the brass mechanism. You can use this Conti spare part on...
31,04 €

Astoria-vipuryhmähaarukka

On this page you will find a chrome plated lever group fork for various lever groups. This fork is responsible for transitioning the lever motion to a vertical motion. This chrome plated group fork can’t be used on the older AL lever groups as used by Astoria and Wega. That part is out of production. This specific item is OEM/Original item suitable for...
74,25 €

La Cimbali HX 150mm

La Cimbali heat exchanger (HX) has a total length of 150mm and a outside diameter of the tube of 42mm.This part is sticks inside the boiler. And it is held in it's place from the boiler side, with a La Cimbali HX ring, then the HX and inbetween the La Cimbali HX and the brewing group there is a o ring to seal it off.Return to the La Cimbali M20 parts...
32,78 €

La Pavoni Europiccola lämpöelementti 1000W 230V

It can happen that your old heating element for your La Pavoni Europiccola, La Pavoni Stradivari, La Pavoni Romantica or of your Gaggia 105-106 burns down or get’s a short in it. This specific model heating element gives 1000W at 240V made by the heating element manufacturer Backer. It is a full stainless steel element, so flange and the element. The...
55,65 €

Faema E61 pieni neliö

Tällä tuotesivulla löydät avainkomponentin Faema E61:lle ja Wega E61:lle. Tämä neliömetsän venttiilin pin on Faema osa viittaus 4161135916 ja Wega osa viittaus W10349.Tämä pieni vasikka venttiili ruuvi ruuvi päälle tiivistys haltija. Neliö on 6x6mm. Keskellä on nainen M3. Tämä on tehty Italiassa.Tätä tuotetta voidaan käyttää Faema E61:n ja Faema E61...
1,44 €

Elektra microcasa boiler knob safety valve

On this page you will find the boiler filling knob of the Elektra Microcasa a Leva. This is quite a unique knob seen it has a integrated safety valve inside the knob, this product has been manufactured by the Italian company Olab. This knob/safety valve has a male 3/8” thread. The Elektra part reference for this item is 00145034
60,82 €

Faema E61 legenda Jubilee Portafilter single

On this product page you will find a single portafilter which is suitable for the Faema E61 Legend and the Faema E61 Jubilé espresso machines.. The part reference number for this item is 2771-135 804.The portafilter has 2 ears oriented at 90 degree. The ears have a thickness of 6,3mm. The spout connection on this portafilter is a 3/8” BSP-G thread. This...
77,86 €

Faema E61 -venttiilikaasu 15,5x7,5x4m m

Tämä EPDM-kaasu on yksi yleisimmin käytetyistä polttoainekokoista. Tämän tiivisteen halkaisija on 15,5 mm sisäinen halkaisijaltaan 7,5 mm ja paksuus 4 mm.Tätä tiivistettä voidaan käyttää eri sovelluksissa vanhojen Faema Lever -espressokoneiden kanssa. kuten tiivistys venttiilin akseleiden sulkemiseen. Mutta löydät tämän tiivisteen Faema E61: stä ja...
0,74 €

Gaggia litteä kumitiiviste

This flat rubber gasket is used on a variety on Gaggia lever brewing groups. This flat gasket is used to seal of the regulator rod on the back of the brewing group. This gasket itself is made from NBR and is made in the Czech Republic.
4,18 €
Gaggia America 1 group heating element Gaggia America 1 group heating element
  • Loppunut varastosta

Gaggia America 1 -ryhmän lämmityselementti

It is quite common that the heating element on the 1 group Gaggia America is broken. Finding the correct heating element for this espresso machine is quite difficult. Seen the espresso machine does have quite a shallow boiler, so a lot of elements won´t fit. This specific model does fit and produces 1200W at 230V. you can also upgrade your single group...
142,62 €

Astoria Wega boiler gasket 190x138x3mm

The boiler gasket on this page is used to seal off the boiler flange with the rest of the boiler. This model of gasket is used with Astoria and Wega espresso machines. The Astoria part number is 12003 and the Wega part number is WY12003. This boiler gasket is made from the material PTFE. The outer diameter is 191mm, the inner diameter is 139mm and the...
40,95 €

Arrarex Caravel: A Beacon of Innovation

1950-luvulla perustettu Arrarex Caravel tuli nopeasti tunnetuksi uraauurtavilla vipukäyttöisillä espressokoneillaan. Caravel, yhtiön lippulaivamalli, yhdisti kompaktin muotoilun ja innovatiiviset vipumekanismit ja mullisti kodin espressonvalmistuksen. Yksinkertaisuutensa ja poikkeuksellisen suorituskykynsä vuoksi rakastettu Caravel on edelleen rakastettu klassikko niin kahvin ystäville kuin keräilijöillekin.

La Cimbali: Täsmätekniikkaa parhaimmillaan

La Cimbali, kahviteollisuuden vankka toimija vuodesta 1912 lähtien, on tunnettu sitoutumisestaan tarkkaan suunnitteluun ja ylivoimaiseen laatuun. Vaikka La Cimbali tunnetaan parhaiten kaupallisista laitteistaan, se valmisti myös poikkeuksellisia vipukäyttöisiä koneita. M1:n kaltaiset mallit osoittivat tuotemerkin omistautumista perinteisen vipukeittimen ja modernin teknologian yhdistämiseen ja asettivat uusia standardeja espressokäsityön huippuosaamiselle.

Faema: Espresson nostaminen taiteeksi

Faema on ollut synonyymi espressokoneiden suunnittelun innovaatiolle ja hienostuneisuudelle perustamisestaan vuonna 1945 lähtien. Vaikka Faema on kuuluisa ikonisesta E61-mallistaan, se on tehnyt jälkensä myös vipukäyttöisten koneiden maailmaan. Nämä tyylikkäät laitteet, joille on ominaista tyylikäs estetiikka ja tarkka tekniikka, inspiroivat edelleen kahvin ystäviä ajattomalla vetovoimallaan ja poikkeuksellisilla valmistusmahdollisuuksillaan.

La Pavoni: La Pavoni: Italialaisen käsityötaidon testamentti

Vuonna 1905 perustetulla La Pavonilla on erityinen paikka kahvinystävien sydämissä kaikkialla maailmassa. Tuotemerkin ikoniset Europiccola- ja Professional-mallit ovat rakastettuja niiden tyylikkään muotoilun ja vertaansa vailla olevan suorituskyvyn vuoksi. La Pavoni -koneet edustavat italialaisen käsityötaidon taidokkuutta ja perinteitä, ja niiden ajaton viehätysvoima lumoaa baristat ja kahvin ystävät tänäkin päivänä.

Bezzera: Pioneering Espresso Excellence

Vuonna 1901 perustetun Bezzeran katsotaan keksineen ensimmäisen kaupallisen espressokoneen, joka loi pohjan nykyaikaiselle kahvikulttuurille. Uraauurtavien innovaatioidensa ohella Bezzera valmisti myös merkittäviä vipukäyttöisiä koneita. Yli vuosisadan innovaation perintönä Bezzera on edelleen luotettava nimi kahviteollisuudessa, ja sitä arvostetaan sen sitoutumisesta laatuun ja huippuosaamiseen.