Etusivulle

The item on this product page is a OEM/Original La Pavoni spare part. This item is a boiler safety valve for various domestic lever espresso machines. The La Pavoni part reference for this item is 396751 This safety valve is only the body and not the internals of this valve.  This boiler valve has at the bottom a male M12 thread. You can use this on the...

Stainless steel measuring spoon 20ml

The o ring on this page can be used as a seal between the lever brewing group and the water boiler of a variety of La Pavoni domestic lever espresso machine models. The La Pavoni part reference for this item is 465128 This o ring is not suitable for the old models, the ones which screw into the boiler. Besides that you can use this o ring on every group....

Puly caff Calcinet espresso machine descaler 1kg

Vibiemme brass lever rod

La San Marco gasket 39,5x50x5,5mmReturn to the  San Marco group parts overview

Brass vähentää 3/8" F x 1/4" M BSP-GTakaisin meidänSopivaYleiskatsaus

Astoria Argenta stainless steel steam pipe

gas membrane

La Cimbali Liberty microcimbali boiler gasket o ring

La Cimbali Liberty microcimbali piston gasket o ring

Rubber flat gasket 13,5x4mm

Rancilio PTFE conical gasket 13.7x8.8x6mm

PTFE gasket 3/8" 22x16.5x2mm

The compression spring on this page can be used in various Lever espresso machines. But to start: Always check the dimensions of your original spring. The product on this page has a overall length of 169mm and a outer diameter of 46mm. The compression spring is made from spring steel and has been galvanized. This compression spring can be used on a...

The water level fitting on this page can be used on various Brasilia espresso machine models. The Brasilia part reference number for this item are 00024.0.00.04 and 00024.0.00.04  This casted brass sight glass fitting has on the machine side a male 3/8” BSP-G thread, on water level side a female 3/8” BSP-G and on the bottom/top a female ¼” BSP-G thread....

La Cimbali heat exchanger (HX) has a total length of 150mm and a outside diameter of the tube of 42mm.This part is sticks inside the boiler. And it is held in it's place from the boiler side, with a La Cimbali HX ring, then the HX and inbetween the La Cimbali HX and the brewing group there is a o ring to seal it off.Return to the La Cimbali M20 parts...

This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 49,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from birch which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles are natural...

Elektra microcasa sight glass 9x148mm

Brass half nut 1/2" 6mm

The gasket on this page is a Polytetrafluoroethylene (PTFE) gasket with the dimensions 35x30x2mm. This specific gasket is used on 3 specific places on the E61 style brewing group (the Faema E61 and Faema E61 legend group use a different size of ptfe gasket). It is used to seal off the top trumpet or drain sleeve, on the side of the group the camme holder...

Elektra microcasa piston

Faema E61 kattila 1 ryhmä 9LKun tämä kattila on korvattava ruostumattomasta teräksestä valmistetulla kattilalla. Osa putkistosta on vaihdettava tai tehtävä uudelleen. On mahdollista, että kattilassa on kuljetuksesta johtuvia pieniä kolhuja. tämä on melko yleistä eikä vaikuta kattilan toimintaan.

La Pavoni piston gasketReturn to the La Pavoni lever group parts overview

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

Rancilio valve spring

On this page you will find a group locking gasket suitable for various Faema lever groups. This gasket goes inbetween the bottom part of the lever brewing group and the espresso machine housing. This gasket has been made from AFM34 of Victor Reinz. The gasket has a outer diameter of 86mm and a thickness of 1mm. It has been made in Germany. This gasket can...

Faema E61 -suodatin 8.5mm nbr. E61-panimoryhmälle saatavilla oleva keskikokoinen portafilter-kaasu. E61:lle on tarjolla kolme paksuuskokoa:8 mm;8,5 mm;9 mm.Jos portafiltteri ei sovi niin kuin haluat, on aina ohuempia panimoja käytettävissä lisätä tiivisteitä:0,5 mm;0,8 mm.Se on aina kätevä ostaa joitakin tiivisteitä ylimääräinen, nähty ne voivat kulua...

Hardened stainless steel insert

On this product page you will find a Stainless steel lever group spring. We had this spring modelled after a original one. The to reach a similar spring rate the coil diameter is slightly different then with a standard steel spring. The spring has a overall length of approximately 168mm and a outer diameter of approximately 46mm. Why approximately? Seen...

On this page you will find the aluminium lever group cover used in a variety of Faema Lever brewing groups. What is the purpose of this item? Mainly esthetical. But it also prevents dust getting in the brewing group mechanism and the chance also reduces that someone get’s its finger stuck in the bearing mechanism. On what kind of lever brewing groups can...

The item on this page is a sight glass gasket which can be used on various older Gaggia espresso machine models. The sight glass on the Gaggia America has 2 seals, a inner and a outer seal. You can use this gasket for both applications. This gasket is made from EPDM in the Czech Republic.

Lip seal 15x8x4

On this page you will find our own Brooks microfiber cleaning cloths. These cloths are ideal for cleaning your espresso machine, coffee grinder or just the work surface around your espresso machine. This is not the standard household dust cleaning cloth your standard find. This type of microfiber is a lot softer used to clean finer surfaces like car...

La San Marco heating element 3 gr 3500W 230/380V L 380mm

Faema E61 on pieni palautusventtiili. Tämä venttiiliopas on sinetöity tälläSormus ja pysyy siinä paikassa, jossa on Ei paluuta kevät.TakaisinFaema E61 venttiilit Yleiskatsaus