This tamper is made from Stainless steel EN 1.4301/AISI 304 with a smooth machined finish. The bases are laser engraved with our logo and the 49,5 mm diameter of the base of the tamper. All our tampers are made in The Netherlands The handle is made from American walnut which has been hand oiled 2 times. Try to avoid contact with water. Seen the handles...

On this page you will find a silicone sight glass gasket, with this seal there is a water tight seal between the glass and the body. This gasket can be used on the Elektra Microcasa lever espresso machine. This item has the Elektra part reference of 00119035 This silicone gasket has  a outer diameter of 15mm a inner diameter of 9mm and a thickness of 8mm.

Are you rebuilding your Faema Marte or first series Mercurio. Then it is always handy to replace the shaft gasket.To replace this part you need to do the following things:Remove the piston from the piston rod; Remove the 2 screws on each side of the top of the group; pull the piston shaft true the top of the lever housing; now you can remove the bottom...

Faema E61:n vesilähtöventtiiliopas. Voit käyttää tätä venttiiliopasta useisiin faema-malleihin. Sitä käytetään lähinnä Faema E61:ssä. Lähde: GaketTakaisinFaema E61 -vesi Yleiskatsaus

Spring for steam valve

Rancilio stainless steel steam pipe

Flat copper gasket 19x13.4x1.5mm 1/4"

Lever spring Stainless steel 46x32x185mm with a cataphoresis coating

Faema Marte/Mercurio lower gasket. this is the gasket which makes the inner sleeve water tight.This sleeve can only be safely removed with a custom made key. you can try it with a punch, this can work. but the chance on damaging the part is also present.Return to the Faema parts overview

The gasket on this product page is used on the Faema E61 brewing groups and the E61 style of brewing groups such as with Rocket, La Scala, Grimac, la Pavoni and Wega. The part reference numbers for this gasket can be found in the extra info tab. This gasket is made from AFM34 from the company Victor Reinz. This gasket has good sealing properties, even...

La Pavoni steam tap bushing

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...

Brewing group cleaning brush with nylon hairs.

Tällä tuotesivulla löydät kukkahitsauksen. Nämä hitsauskortit juotetaan kupariputkien ääriin yhdessä hitsauspähkinän kanssa. Tämä pyöreä pinta sinetöi, kun pähkinä kiristyy. Vasikan materiaalipakkaukset ja nämä sinetit pois venttiilistä. Tätä hitsauspäätekorkin kokoa käytetään pääasiassa painekytkimien tubroimiseen. niin suuria määriä, että tilavuutta ei...

Faema lever group cap Return to the Faema Zodiac lever parts overview

Faema brass cap Return to the Faema Zodiac lever parts overview

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the right side of the group. To be sure that you order the correct side. The rounded where the rounded off...

Crushable copper washer 1/4" 18x14x2mm

La San Marco steam/water valve gasket spring

Astoria heating element 4500W 230/380V L 310mmType                       flangedwatt 4500volt                      230/400length (mm) 310

On this page you will find the front stop for various lever brewing groups. This front stop make sure tha you don’t damage the lever nor the castings of the brewing group itself. This rubber front stop can be used with brands such as Brasilia with part number 01432.0.00.02 , La Pavoni 477021 and Victoria Arduino 17000018 . For La Pavoni it is only...

O ring 23,52x1.78mm epdmReturn to the Faema E61 Legend water inlet parts overview

The handle knob on this page can be used on Faema E61 brewing groups. This handle goes on the brewing group control lever. Originally these were made from Bakelite, but nowadays that isn’t made that much anymore. The Faema part reference fort his item is 4741135910  This plastic lever brewing group handle is made from a shiny plastic. In the middle is a...

Faema Mercurio sight glass cover

La Pavoni piston gasketReturn to the La Pavoni lever group parts overview

Brass nipple 1/4"M x 3/8"M BSP-GTakaisin meidänSopivaYleiskatsaus

La San Marco steam/water valve spring

On this product page you will find the portafilter gasket for the Bezzera Strega. This portafilter gasket is a OEM/original Bezzera spare part. The Bezzera part reference for this item is 7493020 This portafilter gasket has a outer diameter of 73mm a inner diameter of 57mm and a thickness of 7,5mm.

Wega chromed steam pipe

Level probe 1/4 167mm

La San Marco gasket supplementReturn to the La San Marco parts overview

Faema E61 -laajennusventtiilin laajennusTakaisinFaema E61 venttiilit Yleiskatsaus

Vipun panimoryhmä käyttää hieman eri osia, sitten normaali pumpun ajama espressokone. Tämä on sama juttu käytettyjen suihkujen kohdalla. Tämä italialaisen IMS Filtri -yhtiön tekemä suihkuruutu on tästä esimerkki. Tämä suihkunäytös kietoutuu panimoryhmän hihnan ympäri pitääkseen sen paikoillaan. Tämän suihkunäytön ulompi halkaisija on 57 mm Tämä suihku on...

On this page you will find a rubber back stop used with a variety of and newer lever espresso machine brewing groups. You will find this back stop on Astoria and Wega models pre 2001. Currently you can find them on brewing groups used by Bezzera 5473001 , Pavoni 477020, Victoria Arduino 17000018, Wega WY15101 and Brasilia 01431.0.00.02. For Pavoni groups,...

Conti bottomless portafilterReturn to the portafilter overview

This red ball is a level indicator ball. This ball floats inside the water level tube. Seen it’s not always easy to see the water level makes a floating red ball it a lot easier. There are more colours available with different diameter of balls. This red ball has a diameter of 5,8mm and is made in Italy. This type of level indicator can be found in a...