Vibiemme Replica Pistone

Tätä pientä ruostumatonta terästä kevättä käytetään useissa Faema höyry- ja vesiventtiileissä. Tämä puristuskevät pitää jatkuvan paineen höyry- ja vesiventtiilin akselikaasuihin, jotta ne tiivistyvät koko ajan. Tämä koskee myös vanhan E61: n vedenottoventtiiliä ja vipua panivia espressokoneita. Faema-osan viittaus tähän puristuskevääseen on...

Faema E61 höyryventtiili pähkinöitä 23x18x1mm. Tämä PTFE-sinetti luo veden ja ilman tiukan sinetin höyryventtiilin vartalon ja kromilevyn välille.TakaisinFaema E61 höyry/vesiventtiili Yleiskatsaus

Tämä EPDM-kaasu on yksi yleisimmin käytetyistä polttoainekokoista. Tämän tiivisteen halkaisija on 15,5 mm sisäinen halkaisijaltaan 7,5 mm ja paksuus 4 mm.Tätä tiivistettä voidaan käyttää eri sovelluksissa vanhojen Faema Lever -espressokoneiden kanssa. kuten tiivistys venttiilin akseleiden sulkemiseen. Mutta löydät tämän tiivisteen Faema E61: stä ja...

Parker solenoid valve 2 ways base mounting 220/230V 50/60Hz 9WReturn to the Faema E61 Legend water inlet parts overview

On this product page you will find a boiler pressure gauge suitable for a variety of Vibiemme espresso machines. The VBM part reference for this manometer is MANM49025GHIR. The pressure gauge can show a boiler pressure from 0 to 2,5bar. The body of the manometer is 49mm, the frame of the pressure gauge is 57mm. This manometer has a capillary with a female...

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The lower o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 56,75mm. This specific o...

The spring on this product page is used for various applications with various brands. This spring is used in water inlet systems, steam and water valves and non return valves. You will find this model of compression spring with brands such as Brasilia, La Spaziale, Faema, Grimac, Vibiemme and La Scala. This stainless steel compression spring has a outer...

Tällä sivulla löydät höyry- ja vesiventtiilin, jota käytetään useissa Faema-espressokoneissa. Tämä venttiili akseli on Faema osa viittaus 48135879.Tämä venttiilihassi on valmistettu ruostumattomasta teräksestä ja sen kokonaispituus on 76 mm. Loppujen lopuksi miesten lanka on M6. Neliön loppu on 7x7mm.Voit käyttää tätä ruostumattomasta teräksestä...

Complete valve spout 54,6mm

This oddly looking screw is the right brewing group pin used on the Vibiemme lever espresso machine brewing groups. The Vibiemme part reference number for this item is VITEPERNGRDPI  This screw can only be used on the right side of the brewing group. This group screw is made in Italy. You can use this lever brewing group screw on the lever group used on...

Tätä vaskipesua käytetään useissa vanhemmissa Faema vipu espressokoneissa. Faema-osan viittaus tähän kohtaan on 41535931.Tätä pesua käytetään yhdessä puristuskevään kanssa pitääkseen yhtä painetta eri akselivetyille. Löydät tämän kohteen eri sovelluksissa, höyryventtiilit, vesiventtiilit ja veden sisääntuloventtiilit.Ulkoiset halkaisijat ovat 15 ja 9mm....

The portafilter gasket on this product can be used on various lever espresso machines. On brands such as Fiorenzato and Vibiemme. The Fiorenzato part reference number is A1200194  and the Vibiemme part reference number is GUARSOTPISTON. This portafilter gasket has a outer diameter of 65,5mm a inner diameter of 55,5mm and a thickness of 5,5mm. This gasket...

The stainless steel ball on this page has a diameter of 8mm. you can use this stainless steel ball in various applications. They are used in the Faema Zodiac Lever groups in the flow regulator.But the stainless steel ball bearing can also be used in the steam and water valves with the Vibiemme model like the Replica. In this valve it seals off the boiler...

Pakkaus kevät tällä sivulla käytetään erilaisia Faema espresso koneita. Mikä on tämän kevään tehtävä? Tämä kevät on höyry- ja vesiventtiili kevät ikonisessa E61-tyylisessä höyry- ja vesiventtiileissä. Kevät pitää venttiilin kiinni. Faema-osan viite on 4731135884.höyry- ja vesiventtiilipakkaus kevät on valmistettu ruostumattomasta teräksestä. Ulkoinen...

1/4" water charging valve autofill

On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....

La San Marco lever handle. The lever doesn't come with the handle and top screw. these can be ordered seperatelyReturn to the  San Marco group parts overview

Expansion valve nipple

O ring 14x2mm

If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...

On this page you will find a brass steam pipe bushing. But what is a pipe bushing. A pipe bushing makes it possible to move the steam and water wand freely without leaking. So how does it work? Well the pipe bushing has on the valve side 2 o rings, these seal against the side of the inside of the valve. But on the top ring of the pipe bushing there is...

Pieni ruostumaton teräspesukone löytyy erilaisista Faema espressokonemallit, jotka käyttävät E61-tyyppistä höyry-/vesiventtiiliä. Faema-osan viittaukset tähän kohtaan ovat: 4041136008 ja 4054043101Tätä pesukonetta käytetään venttiilin akselin ja tap-pyöräytyksen välillä. Tämä ruostumaton teräspesukone on ulkoinen halkaisijaltaan 9mm ja sisäinen...

Faema E61 expansion valve guide. This guide makes sure that the expansion valve gasket stays in it's place Return to the Faema E61 valve parts overview

Fiorenzato piazza san marco lever group ball bearing. Replacing your old bearing with a new one makes a huge difference in smoothness. Return to the Fiorenzato lever parts overview

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

With this steam valve you can clearly see that there are some resemblances between Faema and Vibiemme. Technically it is as good as identical as a e61 valve, the only difference is that the Vibiemme valve has a stainless-steel ball in the valve. Aesthetically the differences are that the chrome plated tap nut is a lot squarer then the original. And one of...

If you are converting your Faema e61 with a new boiler, it can be practical to order this boiler fitting at the same time. As you can see, the new boiler does not come with this fitting. This fitting, cast and machined from brass, has a ½ ”BSP-G male thread on 2 sides. And on one side a ¼ ”BSP-G female thread. So screw it into the bottom of the HX on one...

EPDM OR 4,47x1,78

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...

Spring for steam valve

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...

This flat PTFE gasket is used on various lever espresso machine brewing groups used on the brands Fiorenzato and Vibiemme. The Fiorenzato part reference number is A1200190  and the Vibiemme part reference number is GUARTEFANPIST. This flat gasket is made from PTFE. The outer diameter is 50mm, the inner diameter is 44mm and the thickness is 4mm. The gasket...

Tämä nbr-sormus, jossa on eritelmät 8 9x1,9 mm. Varmista, ettäEi palautusventtiiliä sinettiä vastaan kehon kehon Ei paluuventtiili.TakaisinFaema E61 venttiilit Yleiskatsaus

Pieni pronssivälilehden spindle löytyy erilaisista Faema espressokoneista. E61-tyylinen höyry- ja vesiventtiili. Faema-osan viittaus tähän kohtaan on 4811135880Tämä tab spindle on valmistettu vaskasta ja sen pituus on 20,8 mm. Faema E61, Faema E61 Legend, Faema E61 Jubilee, Faema President ja Faema Lambro.