Brasilia Portofino Leva

The compression spring on this page is used on various models of the Brasilia espresso machine brand. This specific spring is used with the rubber steam and water valves. The part reference number for this item is 10962.0.00.03  This compression spring is made from Stainless steel. The outer diameter is 10,5mm and the length is 27mm. This steam and water...

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

On this page you will find a lever fork pin suitable for brands such as the Astoria and Wega. Note, there are more versions available This blank steel pin (so they do rust) is the link between the lever and the piston shaft. This pin has been knurled on one side, this side also grabs into the brass lever group fork. This lever pin is a OEM/Origina (part...

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...

On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....

Brasilia lower level fitting

On this page you will find a plastic handle which goes over a lever brewing group lever. This plastic lever handle can be used with a variety of lever brewing groups such as the ones used with Vibiemme Replica, Astoria Rapallo, La Pavoni Bar, La Pavoni Bart, La Pavoni Pub, Wega Antares, Wega Nova, Victoria Arduino Athena, Brasilia Decurtis AL and so on....

Brasilia portofino/gradisca handle

On this page you will find a lever brewing group main spring. This spring is used to generate the pressure. This type of spring is quite common and will find it in a variety of lever espresso machines. This model has a overall length of 140mm and a outer diameter of 46mm. this spring has been made from standard spring steel and after that it got...

The item on this page is a steam and water valve washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item is 12153.0.00.03. This washer is made from machined brass. the outer diameter is 10,7mm, the inner diameter is 8,2mm and the thickness is 2mm. this washer is made in Italy. You can use this brass washer on...

On this page you will find a heating element suitable for various Brasilia espresso machine models. This specific heating element is suitable for a 1 group espresso machine. The Brasilia part reference is 00614.2.00.08 This heating element produces 1800W at 230V, there are 4 connecting poles. The element has a immersed length of 170mm. The flange on this...

Astoria lever group fork pre 2001 Return to the Astoria lever parts overview

This steam pipe bushing is a important element in the sealing and functioning of a steam and water valve. This bushing is pushed down on one side with a spring, this bushing has on the other side a hollow shape so that the ball of the steam and water valve can slide smoothly over the brass. This brass bushing has multiple dimensions. The external diameter...

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

Yksi yleisimmistä asioista. Miespuolinen pronssi plug. Tämän sivun plus löytyy useiden espressokonevalmistajien, kuten AstoriaFaema, La Spaziale ja Wega.Tämä spesifinen plug on mies 1⁄4"BSP-G-lanka. Tämän pistokkeen korkeus on 13 mm ja tämän pistokkeen ranskakoko on 17 mm.

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...

Safety valve 1/2"1,8 Certif CE PED IV

Rancilio steam/water valve joint o ring 12,1x2,7mm

Conical portafilter gasket 66x56x6mm

The item on this product page is a steam and water valve elastic washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item 01286.0.00.03  These washers are used in a pair in combination with the articulating valve screw, which is used on the steam and water valves. You can use these washers on the Brasilia...

Tällä sivulla löydät sormuksen, jonka halkaisija on 1,9 mm ja sisäinen halkaisija on 7,2 mm. Tätä spesifistä sormusta käytetään erilaisissa Expresso-koneiden sovelluksissa. Esimerkkinä Expobar Veden sisääntuloventtiilissä. Faema in the cappuccinatore.Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg ja La Carimali espressokoneen höyry- ja...

On this page you will find a lever piston gasket. This gasket size is one of the most commonly used size in lever espresso machines. This piston gasket has a outer diameter of 52mm a inner diameter of 40mm and a height of 7mm. The gasket itself has been made from NBR. You can use this gasket with lever brewing groups made by the brands Astoria, La...

The valve axle on this page is suitable for a variety of Brasilia espresso machine models. This steam and water valve shaft has the Brasilia part reference of 12046.4.00.09 This steam and water valve shaft has a overall length of 100mm and comes with a sealing gasket already installed. You can use this valve not in combination with the ceramic valves....

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The upper o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 58,74mm. This specific o...

On this page you will find a portafilter gasket specially suited for lever espresso machine brewing groups. This specific portafilter gasket is suitable for brands such as the Astoria, Pavoni, Wega, Victoria Arduino, Fiorenzato and Brasilia lever groups. (seen they are the same model of group) This specific gasket has been made from NBR. This gasket has a...

The o ring on this product page is used on various Brasilia steam and water valves on various models. The Brasilia part references for this item are 05825.0.00.02 and 0582500002. This o ring is made from EPDM. The cord diameter is 2,62mm and the internal diameter is 25,07mm. This o ring is made in Italy.  You can use this o ring on the Brasilia Century,...

Brasilia portafilter single spout Return to the portafilter  overview

On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The lower o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 56,75mm. This specific o...

Brasilia portofino chromed steam pipe

The sight glass on this page can be used on various Vibiemme espresso machine models. The Vibiemme part reference for this item is MATECVELI140  This sight glass has a outer diameter of 11mm and a overall length of 140mm. this sight glass has silk printing on the glass. There is on the back a red line and on the front the lettering of max and min. This...

The gasket on this page is made from copper instead from PTFE or a fibre material. The copper gasket is mainly used on Rancilio espresso machines. The Rancilio part number for this item is 27400001. This copper gasket is from the flat type, so not a copper compression gasket. The outer diameter of this gasket is 24mm, the inner diameter is 21mm and the...

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

On this page you will find a OEM/Original shock absorber for the Astoria and Wega lever brewing groups. This absorber is located inside the lever fork. So when the lever is released by accident this rubber shock absorber will absorb some of the force. This absorber is also used when the lever is in rest position This shock absorber can be used on the...

The nut on this page is a M3 nut made from brass. You will find this type of nut on variety of steam and water valves of  Astoria and Wega espresso machines. The Astoria part reference for this item is 23050 and the Wega part reference is WY23050. This brass nut has a metric female thread of M3. The nut has made according to specifications of UNI 5587 and...