Brasilia Portofino Leva

The item on this product page is a steam and water valve elastic washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item 01286.0.00.03  These washers are used in a pair in combination with the articulating valve screw, which is used on the steam and water valves. You can use these washers on the Brasilia...

On this product page you will find the injector tube for various lever espresso machine groups. For example used on Astoria, Wega and La Pavoni groups. This item is a OEM/original Astoria/Wega spare part, but can be used with La Pavoni brewing groups. The overall length of this tube is 140mm and the tube has a outer diameter of 12mm. the fittings screws...

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...

On this page you will find a o ring with the dimensions 10,78x2.62mm. It is made from FKM (viton is a registered trade brand, but the material is identical) This o ring is used in a variety of locations in espresso machines. It is used with steam and water wands in espresso machines with brands like: Marzocco, Casadio, Vibiemme, Grimac, Cimbali and Faema....

On this page you will find a rubber back stop used with a variety of and newer lever espresso machine brewing groups. You will find this back stop on Astoria and Wega models pre 2001. Currently you can find them on brewing groups used by Bezzera 5473001 , Pavoni 477020, Victoria Arduino 17000018, Wega WY15101 and Brasilia 01431.0.00.02. For Pavoni groups,...

The water level fitting on this page can be used on various Brasilia espresso machine models. The Brasilia part reference number for this item are 00024.0.00.04 and 00024.0.00.04  This casted brass sight glass fitting has on the machine side a male 3/8” BSP-G thread, on water level side a female 3/8” BSP-G and on the bottom/top a female ¼” BSP-G thread....

On this page you will find the inner liner for a brewing group. This inner liner is used with a variety of espresso machine brands. This brass liner is pushed into place. It will be sealed off with 2 o ring, a bottom and a top o ring. To remove this liner it’s basically installation but the other way around. You can find this liner in a variety of lever...

Bezzera bottomless portafilterReturn to the portafilter overview

On this page you will find a lever piston gasket. This gasket size is one of the most commonly used size in lever espresso machines. This piston gasket has a outer diameter of 52mm a inner diameter of 40mm and a height of 7mm. The gasket itself has been made from NBR. You can use this gasket with lever brewing groups made by the brands Astoria, La...

Tämän sivun venttiilikaappi on yksi yleisimmistä tasaisista tiivisteistä, joita voit löytää espressokoneesta. Tämä tiiviste on valmistettu NBR: stä ja sillä on 13 mm: n ulompi halkaisija 4 mm: n ja 4 mm: n paksuus.Tämä tyyppi on peräisin Faema espressokoneista. Faema E61, Faema President, Faema Lambro Faema Urania ja niin edelleen.Tämän jälkeen näet tämän...

The nut on this page is a M3 nut made from brass. You will find this type of nut on variety of steam and water valves of  Astoria and Wega espresso machines. The Astoria part reference for this item is 23050 and the Wega part reference is WY23050. This brass nut has a metric female thread of M3. The nut has made according to specifications of UNI 5587 and...

The steam pipe spring on this page is suitable for a variety of espresso machine brands, it’s also a universal item. This spring make sure that you can leave your steam tube in a fixed position. If there is no spring, it will fall back to the lowest point. This spring has a external diameter of 12mm and a overall length of 15mm and is made from stainless...

Brass lever valve with PTFE lining

This sight glass fitting is used on a variety of espresso machine brands such as Vibiemme, La Scala, Brasilia and Gaggia. The Brasilia part reference is 00089.0.10.04 , the Gaggia reference is LV0505 and the Vibiemme (VBM) part references are RACCP227 and RACCP427. This sight glass fitting has a male 3/8” BSP-G thread. The central hole is for the sight...

On this page you will find the front stop for various lever brewing groups. This front stop make sure tha you don’t damage the lever nor the castings of the brewing group itself. This rubber front stop can be used with brands such as Brasilia with part number 01432.0.00.02 , La Pavoni 477021 and Victoria Arduino 17000018 . For La Pavoni it is only...

On this page you will find a heating element suitable for various Brasilia espresso machine models. This specific heating element is suitable for a 1 group espresso machine. The Brasilia part reference is 00614.2.00.08 This heating element produces 1800W at 230V, there are 4 connecting poles. The element has a immersed length of 170mm. The flange on this...

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...

The crushable copper gasket on this page can be used with various applications on Brasilia espresso machines.  For instance, on sealing off steam and water tubes and as a gasket on various boiler fitting applications. The Brasilia part reference for this item is 01386.0.00.02  This copper gasket has a outer diameter of 23mm a inner diameter of 17mm and a...

On this page you will find a lever fork pin suitable for brands such as the Astoria and Wega. Note, there are more versions available This blank steel pin (so they do rust) is the link between the lever and the piston shaft. This pin has been knurled on one side, this side also grabs into the brass lever group fork. This lever pin is a OEM/Origina (part...

Brasilia lower level fitting

Tällä sivulla löydät sormuksen, jonka halkaisija on 1,9 mm ja sisäinen halkaisija on 7,2 mm. Tätä spesifistä sormusta käytetään erilaisissa Expresso-koneiden sovelluksissa. Esimerkkinä Expobar Veden sisääntuloventtiilissä. Faema in the cappuccinatore.Vibiemme, La Scala, Fiamma, Grimac, Brasilia, ECM Heidelberg ja La Carimali espressokoneen höyry- ja...

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The lower o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 56,75mm. This specific o...

The sight glass on this page can be used on various Vibiemme espresso machine models. The Vibiemme part reference for this item is MATECVELI140  This sight glass has a outer diameter of 11mm and a overall length of 140mm. this sight glass has silk printing on the glass. There is on the back a red line and on the front the lettering of max and min. This...

This Conical PTFE gasket can be used on a variety of Brasilia espresso machines. For this item there is a Brasilia part reference of 00810.0.00.02. This gasket has a conical shape. The outer diameter of this PTFE gasket is 14,5mm, the inner diameter is 10mm and the thickness is 5mm. This gasket can be used on the rubber as well as on the ceramic valves....

On this page you will find a OEM/Original shock absorber for the Astoria and Wega lever brewing groups. This absorber is located inside the lever fork. So when the lever is released by accident this rubber shock absorber will absorb some of the force. This absorber is also used when the lever is in rest position This shock absorber can be used on the...

Astroia CMA style complete lever brewing group

The item on this page is a steam and water valve washer, used on various Brasilia espresso machines. The Brasilia part reference number for this item is 12153.0.00.03. This washer is made from machined brass. the outer diameter is 10,7mm, the inner diameter is 8,2mm and the thickness is 2mm. this washer is made in Italy. You can use this brass washer on...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

The valve axle on this page is suitable for a variety of Brasilia espresso machine models. This steam and water valve shaft has the Brasilia part reference of 12046.4.00.09 This steam and water valve shaft has a overall length of 100mm and comes with a sealing gasket already installed. You can use this valve not in combination with the ceramic valves....

Yksi yleisimmistä asioista. Miespuolinen pronssi plug. Tämän sivun plus löytyy useiden espressokonevalmistajien, kuten AstoriaFaema, La Spaziale ja Wega.Tämä spesifinen plug on mies 1⁄4"BSP-G-lanka. Tämän pistokkeen korkeus on 13 mm ja tämän pistokkeen ranskakoko on 17 mm.

On this product page you will find the bearing pin used in a variety of lever espresso machines, such as Astoria, Wega, Pavoni and Brasilia. This pin has a knurled middle piece. On that location the chrome plated lever fork will be installed to. And next to that you will get 2 bearings. These are secured with 2 shaft clips. This item is OEM/Original...

On this page you will find a lever brewing group main spring. This spring is used to generate the pressure. This type of spring is quite common and will find it in a variety of lever espresso machines. This model has a overall length of 140mm and a outer diameter of 46mm. this spring has been made from standard spring steel and after that it got...

Gudgeon pin lever group

On this product page you will find the connection between the lever and the lever group itself. In the top of this casted item you will screw the lever itself.  There are 2 holes. 1 of them has a bushing inside so that there is some axial movement possible. In the fixed hole goes the bearing shaft. In the movable hole goes a pin to make a connection with...