Vibiemme Replica manual

Vibiemme chromed lever sleeve

This o ring is one of the most common parts in the world of espresso machines. The main function of this o ring is to seal off a flanged solenoid valve. Every flanged solenoid valve uses 2 of these. But you will also find them in applications like steam and water valves and water inlet taps. The o ring has a wire diameter of 1,78mm and a internal diameter...

The gasket on this product page is a PTFE flat gasket which can be used on various applications such as boiler gaskets, water inlet gaskets and steam and water valves. This gasket is used on brands such as San Remo, La Scala, Grimac, Nuova Simonelli, Victoria Arduino and Gaggia. This gasket has been made from PTFE. The outer diameter is 18mm the inner...

The PTFE gasket on this page is used in a variety of E61 Style of brewing groups as well as the Faema E61 brewing group. You can find the gasket with brands such as La Pavoni, Faema, Wega, Grimac, Bezzera, La Scala, Vibiemme and Brasilia. The list of part and model references can be found in the extra info tab. This gasket has been made from PTFE. The...

Vibiemme brass lever rod

This brass bushing is used on a variety of older Faema lever espresso machines. The Faema part reference for this item is 4151135931. This bushing is used, in combination with a compression spring, to hold a equal pressure to various shaft gaskets. You will find this item in various applications, steam valves, water valves and water inlet valves. The...

With this steam valve you can clearly see that there are some resemblances between Faema and Vibiemme. Technically it is as good as identical as a e61 valve, the only difference is that the Vibiemme valve has a stainless-steel ball in the valve. Aesthetically the differences are that the chrome plated tap nut is a lot squarer then the original. And one of...

Lucifer solenoid valve 2 way base mounting 220/240V 50/60Hz

The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...

Ball valve 1/4M 1/4F

This EPDM gasket is one of the most commonly used sizes of gasket. This gasket has a outer diameter of 15,5mm a inner diameter of 7,5mm and a thickness of 4mm. This gasket can be used in various applications with the old Faema Lever espresso machines. such as a gasket for sealing off valve shafts. But you will find this gasket in the Faema E61 and the...

O ring 14x2mm

Faema E61 brass washer 5.4x3mm is fitted between the gasket valve holder and between the valve guides Return to the Faema E61 group parts overview

On this page you will find a brewing group spray nozzle. This nozzle is one of the most used spay nozzles used in the world of espresso machines. The nozzle has a outer diameter of 30mm and the male thread, which threads into the brewing group, is M10x1mm. What is the purpose of having a nozzle. Well the spray nozzle is located above the shower screen....

Locking group gasket

EPDM OR 4,47x1,78

This O ring in nbr with the specifications 8,9x1,9mm. Makes sure that the brass non return valve seals against the body of the non return valve. Return to the Faema E61 valve parts overview

Faema E61 brass small non return valve. This valve guide is sealed by this o ring and kept on it's place with the non return valve spring. Return to the Faema E61 valve parts overview

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the top exhaust valve. When the lever is in the raised position this spring will keep the drain valve in the closed position. This stainless-steel compression spring has an outer diameter of 14mm. The length of...

Complete valve spout 54,6mm

If you are rebuilding your Faema e61 with a new boiler it might be handy to order this boiler fitting along with it. Seen the new boiler isn’t supplied with this fitting. This brass casted and machined fitting has on 2 sides a male ½”BSP-G thread. So to screw it on one side in the HX on the boiler and for the other side to the brewing group. This item has...

VBM e61 style rebuild kit

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

The item on this page is a gasket holder which is used in a variety of E61 brewing groups. You can find this item in some valve assemblies used on Faema, Pavoni and Wega espresso machines. For some brands this item is also used in the steam/water and water inlet valves. This brass gasket holder has 2 threads. 1 female and one male. The female thread is a...

On this page you will find a o ring which has a cord diameter of 2,62mm and a internal diameter of 20,63mm. the material for this o ring is Viton. The application in espresso machines for this o ring is really broad. This ranges from application in brewing groups with brands like ECM Heidelberg, la Scala, Bezzera and Brasilia. But also the application in...

Faema E61 brass brewing group gigleur 0.6mm. this is also suitable for most of the E61 style brewing groups and a variety of modern commercial espresso machines  Return to the Faema E61 group parts overview

On this product page you will find a heating element suitable for various VBM heating elements. This heating element is suitable for 2 group Vibiemme boilers. The Vibiemme part reference is ELETRES2G4023. This heating element produces 4000W at 230V and has 4 connecting poles. The immersed length of the heating element is 330mm. the heating element has a...

Return to the Faema E61 valve parts overview

The gasket shown on this product page can be used on various Vibiemme espresso machine boilers. The Vibiemme part reference for this item is GUARFL205T  This boiler gasket has a outer diameter of 165mm a inner diameter of 150mm and a thickness of 3mm. This gasket has been made from PTFE. Made in Italy. You can use this boiler gasket on the Vibiemme Cubo,...

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

Probably the most used pressure switch used on the Asco P302/6 a 3 phase pressure switch. This pressure switch has been used espresso machines like: La Marzocco, Faema, Cimbali, Astoria, Wega, Nuova Simonelli, La Spaziale, San Remo and so on.The brand Asco used to be the company Sirai, since a while this name has changed but the product remains the same....

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...

Vibiemme upper sleeve

E61 style upper sleeve. not for faema e61

The item on this product page is a stainless steel water filter, this filter is used with various espresso machine brands in the top of the brewing group. You can find this filter with brands such as ECM Heidelberg, San Remo, Vibiemme, La Scala, Bezzera, Grimac, Astoria, La Pavoni and wega. This stainless steel water filter has a outer diameter of 8,5mm...

The spring on this page is used in the Faema E61 and various other of E61 style of brewing groups. This spring is used as a return spring for the bottom exhaust valve. When the lever is in the lowest position the valve assembly will push this spring inward and the exhaust valve will open completely. This will make sure that all the exhaust water goes out...