Faema President spare parts

On this product page you will find a Stainless steel lever group spring. We had this spring modelled after a original one. The to reach a similar spring rate the coil diameter is slightly different then with a standard steel spring. The spring has a overall length of approximately 168mm and a outer diameter of approximately 46mm. Why approximately? Seen...

It is quite common that the supports of your glass at the back are rusted and the bolts are stuck. We have made a new set of support sets for the glass plates from stainless steel. This support set can be used on all the Faema e61Faema President lever espresso machines which use the glass plate. But also on the late models Urania which use the glass...

Every Faema E61 and Faema President has a glass plate at the back of the espresso machine. This glass plate is held in place with a set of 4 glass plate screws. On this page you can find a set of 4 aluminium screws which look like the original screws used for holding the glass in its place. Don’t overtighten them, it’s only there that the glass doesn’t...

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

The PTFE gasket on this page can be used on various E61 style and Faema E61 brewing groups. You can use this gasket on the E61 style brewing groups of the brands like La Scala, Grimac, Wega and La Pavoni.  The part and model references can be found in the extra info tab. This PTFE gasket has a outer diameter of 36mm a inner diameter of 30mm and a...

This boiler pressure gauge can be found from one of the earliest Faema E61 espresso machines as well for the Faema President lever espresso machines. This pressure manometer has a pressure reach of 0 to 3 bar. The body diameter is 52mm the rim has a diameter of 71mm. At the back is a fitting which is a male 1/8”BSP-G thread. The manometer has been...

Every brewing group uses a portafilter gasket. In this case it is a 73x57x9mm gasket. In this case they are made from a food grade nitrile butadiene rubber(Nbr)The OD and ID of 73x57mm is quite a standard size. You will see this size with brands like Expobar, Vibiemme (VBM), La Scala, Bezzera, Faema and Azkoyen. This doesn’t mean that these brands don’t...

On this page you will find a group locking gasket suitable for various Faema lever groups. This gasket goes inbetween the bottom part of the lever brewing group and the espresso machine housing. This gasket has been made from AFM34 of Victor Reinz. The gasket has a outer diameter of 86mm and a thickness of 1mm. It has been made in Germany. This gasket can...

It is not uncommon that the back lid glass of your Faema E61 or Faema President breaks. Glass remains fragile in the end. On this page you will find a replacement glass for the 2 group espresso machine. The get rid of the sharp edge the glass has been cut with a small chamfer. This glass plate comes without a stickers. We do only have the stickers for the...

This small stainless steel spring is used in various Faema steam and water valves. This compression spring keeps a constant pressure on the steam and water valve shaft gaskets, so that they will seal all the time. This is also the case for the water inlet valves for the old E61 and lever brewing group espresso machines. The Faema part reference for this...

On this product page you will find a replacement glass for a Faema E61 1 group and a Faema President 1 group lever espresso machine. The outer dimensions of the glass are 365mm by 165mm The distance between the holes is not identical horizontally. Vertically the distance it is about 85mm from centre to centre. For the horizontal distance, centre to centre...

On this page you will find a brass gasket holder, this holder is used in steam and water valves on the older Faema E61 and Faema lever espresso machines. The Faema part reference for this item is 2151136654. This brass gasket holder has on one side space for the valve gasket, this gasket is 13x4x4mm. On the other side is a space for the tap spring, which...

A lever brewing group uses slightly different parts then a normal pump driven espresso machine. This is the same story for the shower screens used. This shower screen made by the Italian company IMS Filtri is a example of this. This shower screen clamps around the sleeve of the brewing group to keep it into place. The outer diameter of this shower screen...

On this product page you will find a heating element which is really well suited to be installed in a Faema E61 2 group boiler. It runs on single phase and still gives enough power to power a 2 group E61. This heating element produces 2440/2900W at 220/240V the element has 4 wiring poles. In the middle of the heating element is also space for a heating...

This PTFE gasket is used in the Faema E61 brewing groups, this also includes the modern Faema E61 brewing groups. The Faema part reference for this item is 4701136003. In the antique Faema E61 espresso machines it is also used to seal off the inlet of the water inlet, on the valve guide side. This gasket has been made from PTFE. The outer diameter is 26mm...

The sight glass on this page is used on a variety of Lever espresso machines by the brand Faema. This sight glass can be used on models such as the Faema E61, Faema President and the Faema Lambro espresso machine. The sight glass has a outer diameter of 12mm and a overall length of 175mm. This sight glass has been made in Italy. The gasket you need for...

Faema guide ring Return to the Faema Zodiac lever parts overview

The paper gasket is one of the items you rarely find as a OEM or Original Item. But it is one of the most important items to keep your machine functioning. Over time the brewing group and portafilter locking systems wears, so there will be more space then original. This small spaces can be filled with the paper shims. This can fix the problems of not...

The compression spring on this page is used in a variety of Faema espresso machines. What is the function of this spring? This spring is a steam and water valve spring in the iconic E61 style of steam and water valves. This spring holds the valve closed. The Faema part reference for this compression spring is 4731135884. The steam and water valve...

The valve spring on this page is used in the Faema Zodiac group type, not all brewing groups use this model. This spring is there to keep pressure on the stainless steel ball bearing of 8mm. This valve spring is made from stainless steel and has a outer diameter of 8mm and a overall length of 20mm.

Stainless steel double filterbasket for a Faema E61 brewing group. This basket can contain 12grams of coffee. The width of the basket is 70mm and the height of the basket is 22mm.if you are looking for a single filterbasket click there. Return to the Faema E61 group parts overview

The bottomless portafilter on this page can be used on a variety of Faema espresso machines. This bottomless portafilter can be used on the antique lever espresso machines as well on the E61 brewing groups. This bottomless portafilter comes with a standard style of handle. The ear orientation is at 90 degrees. The thickness off the ears is 7,2mm. This...

On this product page you will find a brass washer. This brass washer is used in the iconic steam and water valve used on the Faema E61 espresso machines. This washer prevents that the shaft gaskets are being destroyed with the threads on the valve shaft. The Faema part reference for this part is 4051050569  This brass flat washer has a outer diameter of...

On this product page you can find a steam and water valve knob suitable for a variety of older Faema lever espresso machines. Note: this knob isn’t made from Bakelite like the originals. This plastic steam and water valve has in the middle of the knob a square bushing which can accept a shaft of 7x7mm. The knob has been made in Italy. This steam and water...

With machines which are around 60 years old it is not uncommon that you get corrosion in some parts. With the Flanges used on the Faema E61, Faema President and the Faema Lambro it is quite common to find pin holes. These holes leak air or water in some cases. This flange has been made for the heating element side of the Faema E61/President and Lambro...

On this product page you will find the black L shaped plastic attachments for the side panels on Faema E61 and Faema President espresso machines. These side panels are mirrored from each other so they are not interchangeable. To install them you need to screw 3 small screws in the back. They are made in Italy. You can use them on the Faema E61, 1 to 4...

The sight glass gasket on this page is used in a variety of older Faema espresso machines such as the Faema E61, Faema President and Faema Lambro. This gasket has been made from EPDM. The outer diameter of this gasket is 21mm the inner diameter is 11,5mm and the thickness is 5mm. This gasket has been made in Germany.

The element on this product page is ideal for your antique lever espresso machine, or Faema E61 espresso machine. This heating element has the typical Faema type of brass flange. The element is powered at 230V and supplies 1500W. The immersed length of the element is just 145mm. The heating element gasket used for this element has a outer diameter of 57mm...

On this product page you will find a plexiglass for various Faema models such as the Faema E61 and the Faema President lever espresso machine. The dimensions off the cup warming plexiglass for the Faema 1 group are only the measurements of the width and length of the U shape. The length of this plexi is about 300mm and the width is 220mm. This plexiglass...

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

On this product page you will find a anti vacuum valve. This valve is made completely out of brass and can be easily disassembled. This type of anti vacuum valve is used with quite a lot of espresso machine brands. This valve has a male ¼”BSP-G thread. The o ring inside the valve is made from HNBR, but the o ring end stop is made from PTFE. As mentioned...

The spring on this page is one used in the flow regulation mechanism of the Faema Zodiac brewing group. The spring has been made out of stainless steel and has an outer diameter of 14mm and a overall length of 23mm. This item can be used in a variety of lever brewing groups made by Faema, but if you are not sure always send us a message to verify this.

It is quite common that the rubber feet of your Faema E61, Faema President, Faema E61 Legend or Faema E61 Jubile will break down. This can be due to age, cracking or just moving around. These rubber feet go in the bottom of the aluminium feet used on all these models, the modern adjustable feet have the part reference of 3515-135 857 and the fixed feet at...

The element shown on this product page can be ideal to make from your 220/230V Faema E61 a 110V model. This heating element has the typical Faema type of brass flange. The element is powered at 110V and supplies 2600W. The immersed length of the element is just 350mm. The heating element gasket used for this element has a outer diameter of 57mm a inner...

Have you ever wanted to convert your single group Faema lever espresso machine from a 220-230V version to a 110V version, now you can. The heating element on this product page is suitable for installation on various antique Faema Lever groups and regular Faema E61 groups. This heating element has the typical Faema type of brass flange. The element is...

On each side of the aluminium casting used on the Faema Lambro, Faema President and the Faema Urania you will a pressed bracket. These brackets guide the bearings over the flattened-out surface on this bracket. The article listed on this page is for the left side of the group. To be sure that you order the correct side. The rounded where the rounded off...