Victoria Arduino Athena 2006 - varaosat

Ode 3 way solenoid valve 1/4" 1/4" 220/230V  DN1,5mm. 

On this page you will find a plastic handle which goes over a lever brewing group lever. This plastic lever handle can be used with a variety of lever brewing groups such as the ones used with Vibiemme Replica, Astoria Rapallo, La Pavoni Bar, La Pavoni Bart, La Pavoni Pub, Wega Antares, Wega Nova, Victoria Arduino Athena, Brasilia Decurtis AL and so on....

Faema spring for P4 valve. Suitable for:CodeProducer30370040 Expobar4731-103918 Faema4731103918 Faema08389900 Futurmat-Ariete10391803 Futurmat-ArieteL165/4 Marzocco311427 Pavoni9007705 Reneka10402014 SanremoMOLLAASTAREVO VibiemmeMOLLAASTARUBK Vibiemme

Vipun panimoryhmä käyttää hieman eri osia, sitten normaali pumpun ajama espressokone. Tämä on sama juttu käytettyjen suihkujen kohdalla. Tämä italialaisen IMS Filtri -yhtiön tekemä suihkuruutu on tästä esimerkki. Tämä suihkunäytös kietoutuu panimoryhmän hihnan ympäri pitääkseen sen paikoillaan. Tämän suihkunäytön ulompi halkaisija on 57 mm Tämä suihku on...

Rancilio steam/water valve joint o ring 12,1x2,7mm

On this page you will find a paper shim, these shims are used to fill up the wear of the brewing group and or the wear on the portafilter. This shim is placed above the portafilter gasket itself which makes it possible to make fine adjustments. This portafilter shim has a outer diameter of 66mm a inner diameter of 58mm and a thickness of 0,8mm This paper...

On this page you will find a portafilter gasket specially suited for lever espresso machine brewing groups. This specific portafilter gasket is suitable for brands such as the Astoria, Pavoni, Wega, Victoria Arduino, Fiorenzato and Brasilia lever groups. (seen they are the same model of group) This specific gasket has been made from NBR. This gasket has a...

Brass puoliksi 1/2" BSP-G 6mmTakaisin meidänSopivaYleiskatsaus

Nuova Simonelli heating element 3/4 group 5000W 230/380V L 570mm

The P203T01 is also manufactured by the company Asco, in the past the name of these pressure switches was Sirai. This name change happened for all the products of Sirai. This Asco Pressure switch is a 2 pole instead of a 3 pole pressure switch. With a full plastic cover. The P203T01 is a slightly lighter pressure switch. The pressure of this switch can be...

Conical portafilter gasket 66x56x6mm

Ball Valve 3/8 MF

On this product page you will find a pressure switch made by the company Asco, previously Sirai. This model is the P303 T01. This pressure switch is rated for a maximum contact load of 20A n 3 poles. The pressure switch can be adjusted between the 0,5bar and the 1,4bar. The fitting on the bottom is a ¼” BSP-G thread. For a tube between 4-6mm. The maximum...

La Spaziale o ring 11,1X1,78mm

Nuova Simonelli heating element gasket 67x55x3mm

Seeger ring 9mm

Faema No stop valve fitting. pitch 1mm. Suitable for:CodeProducer30370010 Expobar4851117523 FaemaL168/0 Marzocco312226 PavoniRACC3FRUBKO VibiemmeRACCGUIASTEVO Vibiemme

Tällä sivulla löydät lämmityselementin, jonka olimme valmistaneet AFM34:stä elintarviketurvallisen kuitumateriaalin, joka on valmistettu Saksassa. Tämän lämmityselementin halkaisija on 57 mm sisäinen halkaisija 43 mm ja paksuus 3 mm. Tätä lämmityselementtiä voidaan käyttää useissa lämmityselementeissä, kuten Faema E61, Faema E61 Legend, Faema E61 Jubile,...

Steam and water valve complete. suitable forAurora BrugnettiBFC roayl;Brasilia;Faema;La ScalaSV SABVictoria Arduino

Nuova Simonelli heating element 2 gr 3000W 230/380V Type flangedwatt 3000volt 230/380vlength (mm) 340

Split pin 2x10. Suitable for:CodeProducer94.00092 Carimali30370110 Expobar4061024965 Faema05160007 Futurmat-ArieteL165/8 Marzocco9007709 Reneka10806370B Sanremo

On this page you will find a certified boiler safety valve, it has CE-PED. This boiler safety valve is one of the most common types around. This valve is pre-set at 2,0 bar and can’t be changed. On the inside of the valve is a FKM gasket, the spring installed is made from stainless steel. The steam discharge rate when opened is 969 L/min. This valve has...

Valve shaft sleeve. Suitable for:CodeProducer95.05033 Carimali30370065 Expobar4151-030015 Faema4151030015 Faema03001500 Futurmat-ArieteL165/7 Marzocco313115 Pavoni10402015 SanremoRACCBUSASRBK Vibiemme

On this page you will find the lever fork for various lever brewing groups. One of the holes is for the bearing pin hole and the other one is for transferring the puling motion to the vertical spring motion. This specific lever fork is specifically for lever groups which are pre-2001 lever brewing groups. This item is out of production and not available...

Faema steam valve rod P4/No stop. Suitable for:CodeProducer30370050 Expobar3811-117123 Faema3811117123 Faema11156502 Futurmat-Ariete11156530 Futurmat-ArieteL169 Marzocco311333 Pavoni10402061 SanremoRACCASTARUBK Vibiemme

Gaggia O ring 47,63x3,53mm

On this page you will find a lever brewing group main spring. This spring is used to generate the pressure. This type of spring is quite common and will find it in a variety of lever espresso machines. This model has a overall length of 140mm and a outer diameter of 46mm. this spring has been made from standard spring steel and after that it got...

Faema Steam knob insert. Suitable for:CodeProducer30370130 Expobar4831131214 FaemaL165/MV Marzocco

A variety of espresso machines use a extractable brass sleeve inside the brewing group. This brass sleeve needs to be sealed off. There is a upper and lower seal. The lower o ring seal is the one on this page. This o ring has been made from EPDM. The cord diameter of this o ring is 3,53mm and the inner diameter of this ring is 56,75mm. This specific o...

Brass nipple 1/4"M x 3/8"M BSP-GTakaisin meidänSopivaYleiskatsaus

Anti vacuum valve 1/4".

Brass L Fitting 3/8 BSP-G MM Takaisin meidänSopivaYleiskatsaus

O ring  5.7x1.9mm nbr

OR 6x1.2mm

This type of piston gasket is one of the most used models in the lever espresso machine world. But this one is different. Yes the dimensions are the same 52x40x7mm but the material is different then with the standard piston gaskets. They are made from clear silicone. This will make them last a lot longer then the standard ones made from NBR. The type of...

On this page you will find a gasket type which is a beating rubber. This rubber damping rubber is located underneath the lever holder fork. But what does a beating rubber do? Well when you lower the lever and let it go, this rubber prevents that the lever fork smashes into the top casting of the lever group. You will find this beating rubber on the...